2107980 HOSE Caterpillar parts
315C
Rating:
Alternative (cross code) number:
CA2107980
210-7980
2107980
CA2107980
210-7980
2107980
Weight: 1 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 2107980:
Number on catalog scheme:
8
For full view, you need register
Information:
GPS
The "Machine Radio Configuration" utility allows you to change the network number or the frequency channel on a data radio. The "Machine Radio Configuration" utility runs on the AccuGrade display.Note: You can only configure radios that have firmware version 1.4 or greater with this utility. IP radios cannot be configured with this utility.Using the "Machine Radio Configuration" Utility
Start the display in "Service Mode".
From the "Setup Menu – Configuration" screen, press the "Installation" soft key in order to list the items under the "Setup Menu – Installation" screen.
Press the up arrow or the down arrow until "Machine Radio Configuration" is highlighted.
Illustration 1 g01866073
Press the "OK" key. A screen that is similar to Illustration 2 will appear.
Illustration 2 g01360780
Enter the "Network" number. Press "OK" in order to have the display accept the "Network" number. After the "OK" button is pressed, the display will automatically return to the previous screen, Illustration 1.
Press the "Escape" button, that is on the display, in order to exit the "Setup Menu - Configuration" menu. TC900C, CR900 Data Radios
If the AccuGrade system detects a TC900C radio or a CR900, the screen in Illustration 3 will appear.The network number that is shown defaults to "Unknown".
Illustration 3 g01360826
Use the down arrow key and the up arrow key in order to select the required network channel (Network 1–40).
Press the "OK" key in order to save the radio network changes and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same network number as the base station radio that you want to receive GPS corrections. TC450C Data Radio
If the AccuGrade system detects a TC450C radio, the screen shown in Illustration 4 appears.
Illustration 4 g01360826
Note: The TC450C has a selection of up to twenty preset frequency channels.Note: The current radio frequency channel is displayed on start up.
Use the down arrow key and the up arrow key in order to select the channel that is desired.
Press the "OK" key in order to save the radio frequency channel and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same frequency channel as the base station radio that you want to receive GPS corrections. In most areas, licensing is required for 450 Mhz frequencies. Be sure the frequency that is selected is licensed with the customer. "Display's Radio Port"
When a third party radio is used, the Display for the AccuGrade System allows the user to adjust the following communication parameters:
Baud Rate
ParityThe "Display's Radio Port" settings sets the speed at which the Display communicates with the radio. These settings do not affect the speed of data transfer though the air between radios. Refer to the following Steps in order to adjust the "Display's Radio Port" settings.
Illustration 5 g01265962
(1) LCD (2) Soft Key Labels (3) Soft Keys (4) Escape Key (5 ) Next Key (6) Power Key (7) "+" Key (8) Arrow Keys (9) "-" Key (10) "OK" Key (11) Menu Key (12) "Data Card Slot"
To view all options
The "Machine Radio Configuration" utility allows you to change the network number or the frequency channel on a data radio. The "Machine Radio Configuration" utility runs on the AccuGrade display.Note: You can only configure radios that have firmware version 1.4 or greater with this utility. IP radios cannot be configured with this utility.Using the "Machine Radio Configuration" Utility
Start the display in "Service Mode".
From the "Setup Menu – Configuration" screen, press the "Installation" soft key in order to list the items under the "Setup Menu – Installation" screen.
Press the up arrow or the down arrow until "Machine Radio Configuration" is highlighted.
Illustration 1 g01866073
Press the "OK" key. A screen that is similar to Illustration 2 will appear.
Illustration 2 g01360780
Enter the "Network" number. Press "OK" in order to have the display accept the "Network" number. After the "OK" button is pressed, the display will automatically return to the previous screen, Illustration 1.
Press the "Escape" button, that is on the display, in order to exit the "Setup Menu - Configuration" menu. TC900C, CR900 Data Radios
If the AccuGrade system detects a TC900C radio or a CR900, the screen in Illustration 3 will appear.The network number that is shown defaults to "Unknown".
Illustration 3 g01360826
Use the down arrow key and the up arrow key in order to select the required network channel (Network 1–40).
Press the "OK" key in order to save the radio network changes and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same network number as the base station radio that you want to receive GPS corrections. TC450C Data Radio
If the AccuGrade system detects a TC450C radio, the screen shown in Illustration 4 appears.
Illustration 4 g01360826
Note: The TC450C has a selection of up to twenty preset frequency channels.Note: The current radio frequency channel is displayed on start up.
Use the down arrow key and the up arrow key in order to select the channel that is desired.
Press the "OK" key in order to save the radio frequency channel and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same frequency channel as the base station radio that you want to receive GPS corrections. In most areas, licensing is required for 450 Mhz frequencies. Be sure the frequency that is selected is licensed with the customer. "Display's Radio Port"
When a third party radio is used, the Display for the AccuGrade System allows the user to adjust the following communication parameters:
Baud Rate
ParityThe "Display's Radio Port" settings sets the speed at which the Display communicates with the radio. These settings do not affect the speed of data transfer though the air between radios. Refer to the following Steps in order to adjust the "Display's Radio Port" settings.
Illustration 5 g01265962
(1) LCD (2) Soft Key Labels (3) Soft Keys (4) Escape Key (5 ) Next Key (6) Power Key (7) "+" Key (8) Arrow Keys (9) "-" Key (10) "OK" Key (11) Menu Key (12) "Data Card Slot"
To view all options
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
315B, 315B L, 315C, 315D L, 316E L, 317B LN, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 32...
307C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 32...
307C, 311C, 311D LRR, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320C, 320D, 3...
307C, 308D, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 315C, 315D L, 316E L, 318C, 318E L, 319D, 319D L, 320B, 320C, 32...
307C, 308C, 315C, 315D L, 319D L, 320B, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 320D RR, 320E LRR, 321D LCR, 322, 322 FM L, 322B, 322B L, 322C, 322C FM, 323D L, 324D FM, 325, 325 L, 325 LN, 325...
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LN, 320D...
308C, 312C, 312C L, 312D, 312D L, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2...
311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320B, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2 L, 321C, 321D LCR, 322, 322 FM L, 322 LN, 322B...
315C, 318C, 319C, 320 L, 320B, 320C, 320E LN, 322, 322 FM L, 322 LN, 323E L, 325, 325 L, 325B, 325B L, 329E, 330, 330B, 330B L, 330C, 330C L, 336E, 345B L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L,...
2177515
HOSE AS
304
304
2120481
HOSE AS
304
304
2745974
HOSE AS
304, 305
304, 305
2745973
HOSE AS
304, 305
304, 305
2745972
HOSE AS
304, 305
304, 305
2745971
HOSE AS
304, 305
304, 305
2108065
HOSE
315C
315C
2108064
HOSE
315C
315C
2107983
HOSE
315C
315C
2107982
HOSE
315C
315C
2228257
HOSE-AIR
315C
315C
2108109
HOSE
315C
315C