AVSPARE.COM
parts catalog

HOSE AS 2389437 - Caterpillar



2389437 HOSE AS Caterpillar parts D3G, D4G, D5G HOSE
Rating:
79
Alternative (cross code) number:
CA2389437
238-9437
2389437
Caterpillar 2389437 HOSE AS
Weight: 0.29 pounds 0 kg.

Buy HOSE AS 2389437 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 2389437:

TRACK-TYPE TRACTOR  D3G   D4G   D5G   Caterpillar
Number on catalog scheme: 8
 
  For full view, you need register

Information:

Start By:a. remove piston cooling jets1. Use Tool (A) and turn the engine flywheel to move the connecting rod cap bolts into a position for removal. 2. Remove bolts (1) and bearing caps (2) from the crankshaft and connecting rod. Remove the lower half of the bearing from caps (2).3. Push the connecting rods away from the crankshaft. Remove the upper halves of the bearing from the rods. Install rod bearings dry when the clearance checks are made. Put clean engine oil on the rod bearings for final assembly.
Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap.
4. Clean the surfaces where the bearing halves fit. Install bearing halves (3) in the rods and caps (2).The serviceman must be very careful to use Plastigage, Tool (B) correctly. The following points must be remembered:...Make sure that the backs of the bearings and the bores are clean and dry....Make sure that the bearing locking tabs are properly seated in their slots....The crankshaft must be free of oil where the Plastigage touches it....Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing....Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed....Do not turn the crankshaft with the Plastigage installed....Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements....Remove the Plastigage before reinstalling the cap.When using Plastigage (B), the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings & Crankshafts, Form No. SEBD0531. 5. Check the bearing clearance with Plastigage. Install caps (2) on the connecting rods making sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod. Tighten the bolts in the number sequence shown as follows: Bolts (4) and (5) are installed on the same side of the rod cap that has the locating pin. The locating pin must extend 4.0 0.5 mm (.16 .02 in) from the rod cap.a. Put Molylube or Fel-Pro C100 Lubricant on the bolt threads and contact surfaces of the bolts and caps.b. Tighten bolts No.

Caterpillar parts catalog:

Caterpillar parts catalog
D3G XL & LGP TRACK TYPE TRACTORS CFC00001-UP (MACHINE) POWERED BY 3046 Engine
D4G XL & LGP TRACK TYPE TRACTORS CFN00001-01071 (MACHINE) POWERED BY 3046 Engine
D5G XL & LGP TRACK TYPE TRACTORS FDH00001-UP (MACHINE) POWERED BY 3046 Engine
D3G XL & D3G LGP Track-Type Tractors BYR00001-UP (MACHINE) POWERED BY 3046 Engine
D4G XL & D4G LGP Track-Type Tractors HYD00001-UP (MACHINE) POWERED BY 3046 Engine
D5G XL & D5G LGP Track-Type Tractors RKG00001-UP (MACHINE) POWERED BY 3046 Engine


Parts hose Caterpillar catalog:

5P1442 HOSE
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
5P1420 HOSE
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
1361953 HOSE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
1440195 HOSE
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1515319 HOSE
315, 315B, 315C, 317B LN, 318B, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
2003103 HOSE AS
AP-1055D, BG-2455D, CB-534D, CB-564D, D3G, D4G, D5G
2389435 HOSE AS
D3G, D4G, D5G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.