2457928 HOSE AS Caterpillar parts
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
Rating:
Alternative (cross code) number:
CA2457928
245-7928
2457928
CA2457928
245-7928
2457928
Weight: 0.51 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 2457928:
Number on catalog scheme:
13
For full view, you need register
Cat SIS web machinery list:
Information:
Illustration 1 g00908522
(1) Rod (2) Dump body position sensorThe dump body position sensor (2) is located on the left rear frame near the pivot pin for the dump body. The rod (1) is connected between the dump body position sensor (2) and the dump body. When the dump body is raised, the rod (1) rotates the dump body position sensor (2), which changes the Pulse Width Modulated signal that is sent to the Power Train Electronic Control Module (Power Train ECM). The adjustment of the rod between the sensor and the dump body is very important. The length of the rod should be 350.0 3.0 mm (13.78 0.12 inch) from the center of both rod ends.After rod (1) has been adjusted, the Power Train ECM will perform a calibration. The dump body position sensor (2) is calibrated by the Power Train ECM when all of the following conditions exist:
The engine is running for one minute with no ground speed.
The hoist control is in the FLOAT position.
The signal from the dump body position sensor is 6 degrees different from the previous calibration.The dump body position sensor (2) is used to limit the top gear while the dump body is up. The Power Train ECM comes from the factory with the top gear value that is set to FIRST gear. The transmission will not shift past FIRST gear until the dump body is down. The top gear value is programmable by utilizing the Electronic Control Analyzer Programmer (ECAP) or the Electronic Technician (ET). The top gear value can be changed to SECOND gear, THIRD gear, or FOURTH gear.The signal from dump body position sensor (2) is also used to control the SNUB position of the hoist control valve. The Power Train ECM will signal the hoist proportioning solenids to move the hoist control valve to the SNUB position when the dump body that is being lowered nears the frame. The speed in FLOAT is reduced in the SNUB position in order to prevent the dump body from contacting the frame too hard.The signal from the dump body position sensor (2) is used to provide warnings to the operator when the truck is moving with the dump body UP.
Parts hose Caterpillar catalog:
330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 385B, 385C L, 385C L MH
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E L, 340D L, 340D2 L
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
325C, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN
330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
325C, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2457927
HOSE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D LN, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D LN, M330D
2405044
HOSE AS
330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2405043
HOSE AS
330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, MH3037
330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, MH3037
2486104
HOSE AS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
1759592
HOSE AS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
2486101
HOSE AS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
330D, 336D L, 336D LN, 345D, 349D L, OEMS
4599061
HOSE AS
CWAC-40
CWAC-40
4599062
HOSE AS
CWAC-40
CWAC-40
3707041
HOSE AS
CWAC-40
CWAC-40
3707040
HOSE AS
CWAC-40
CWAC-40
3705560
HOSE AS
CWAC-40
CWAC-40
3276549
HOSE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D