2459193 HOSE Caterpillar parts
323D L, 323D LN
Rating:
Alternative (cross code) number:
CA2459193
245-9193
2459193
CA2459193
245-9193
2459193
Weight: 1 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
10
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - M30 X 3.5Guide Stud 2
B 138-7576 Link Bracket 1
D 138-7574 Link Bracket 2
E 4C-5593 Anti-Seize Compound 1
F 6V-7030 Micrometer Depth Gauge Group 1
G 373-2633 Alignment Tool 1
Illustration 1 g01414384
Illustration 2 g01414235
Apply Tooling (E) onto the taper of suspension cylinder (6). Use Tooling (D) and a suitable lifting device to install spindle (5) onto suspension cylinder (6).
Illustration 3 g01414468
Install bolts (7). Repeat this step for the opposite side of the spindle.
Use Tooling (G) to align the bolt holes that are in the suspension rod with the bolt holes that are in the steering arm.
Install Tooling (A).
Illustration 4 g01414475
Illustration 5 g01414476
Use Tooling (B) and two suitable lifting devices to position steering arm (1) onto spindle (5). The weight of steering arm (1) is approximately 309 kg (681 lb). Install three of bolts (3) that are separated by 120 degrees. Remove Tooling (B). Tighten three of bolts (3) to a torque of 203 27 N m (150 20 lb ft). Use Tooling (F) to measure the gap between the end of suspension cylinder (6) and the surface of steering arm (1). Loosen three of bolts (3). Install Tooling (B) and two suitable lifting devices. Remove three of bolts (3). Remove steering arm (1).
Illustration 6 g01414050
Install shim pack (4) that is equal to the measurement that was obtained in Step 5 minus 8.6 0.03 mm (0.3386 0.0012 inch). The thickness of shim pack (4) must not be less than 0.64 mm (0.025 inch).
Illustration 7 g01414481
Illustration 8 g01414482
Use Tooling (B) and two suitable lifting devices to position steering arm (1) onto spindle (5). The weight of steering arm (1) is approximately 309 kg (681 lb). Install bolts (3). Remove Tooling (B). Tighten bolts (3) to a torque of 1800 200 N m (1328 148 lb ft). Remove Tooling (A).Note: The expected clearance between the shim pack and the steering arm is 0.00 to 0.13 mm (0.000 to 0.005 inch).
Illustration 9 g01524255
Install bolts (2). Tighten bolts (2) to a torque of 800 50 N m (590 37 lb ft). Tighten bolts (2) by an additional 120 degrees.End By:
Install the service and parking brake.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - M30 X 3.5Guide Stud 2
B 138-7576 Link Bracket 1
D 138-7574 Link Bracket 2
E 4C-5593 Anti-Seize Compound 1
F 6V-7030 Micrometer Depth Gauge Group 1
G 373-2633 Alignment Tool 1
Illustration 1 g01414384
Illustration 2 g01414235
Apply Tooling (E) onto the taper of suspension cylinder (6). Use Tooling (D) and a suitable lifting device to install spindle (5) onto suspension cylinder (6).
Illustration 3 g01414468
Install bolts (7). Repeat this step for the opposite side of the spindle.
Use Tooling (G) to align the bolt holes that are in the suspension rod with the bolt holes that are in the steering arm.
Install Tooling (A).
Illustration 4 g01414475
Illustration 5 g01414476
Use Tooling (B) and two suitable lifting devices to position steering arm (1) onto spindle (5). The weight of steering arm (1) is approximately 309 kg (681 lb). Install three of bolts (3) that are separated by 120 degrees. Remove Tooling (B). Tighten three of bolts (3) to a torque of 203 27 N m (150 20 lb ft). Use Tooling (F) to measure the gap between the end of suspension cylinder (6) and the surface of steering arm (1). Loosen three of bolts (3). Install Tooling (B) and two suitable lifting devices. Remove three of bolts (3). Remove steering arm (1).
Illustration 6 g01414050
Install shim pack (4) that is equal to the measurement that was obtained in Step 5 minus 8.6 0.03 mm (0.3386 0.0012 inch). The thickness of shim pack (4) must not be less than 0.64 mm (0.025 inch).
Illustration 7 g01414481
Illustration 8 g01414482
Use Tooling (B) and two suitable lifting devices to position steering arm (1) onto spindle (5). The weight of steering arm (1) is approximately 309 kg (681 lb). Install bolts (3). Remove Tooling (B). Tighten bolts (3) to a torque of 1800 200 N m (1328 148 lb ft). Remove Tooling (A).Note: The expected clearance between the shim pack and the steering arm is 0.00 to 0.13 mm (0.000 to 0.005 inch).
Illustration 9 g01524255
Install bolts (2). Tighten bolts (2) to a torque of 800 50 N m (590 37 lb ft). Tighten bolts (2) by an additional 120 degrees.End By:
Install the service and parking brake.
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
307B, 307C, 308C, 311D LRR, 311F LRR, 312C L, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
307C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 32...
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LN, 320D...
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
311D LRR, 311F LRR, 312C L, 315C, 318C, 320B, 320C, 320C L, 320D, 320D L, 320E LRR, 321C, 321D LCR, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 325B, 325B L, 325C, 325C FM, 32...
308C, 312C L, 312D, 312D L, 315C, 315D L, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 322...
315C, 318C, 319C, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 322C, 322C FM, 323D L, 323D LN, 323D2 L, 325C, 325C FM, 325C L, 350, 385B
314C, 318C, 319C, 320B, 320B U, 320C, 321C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, ...
319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 321D LCR, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324E, 325C FM, 330C FM
320B, 320C, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L
320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 325C, 330B L, 330C L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 350
320D, 320D FM, 320D GC, 320D L, 323D L, 323D LN
1950052
HOSE AS
M322C, M322D, M322D MH
M322C, M322D, M322D MH
2501652
HOSE AS
M322C, M322D, M322D MH
M322C, M322D, M322D MH
2431980
HOSE AS
1390
1390
2611436
HOSE AS
1390, 541, 551, 552
1390, 541, 551, 552
2431987
HOSE AS
1390, 2590
1390, 2590
2431984
HOSE AS
1390
1390
2666150
HOSE-AIR
323D L, 323D LN
323D L, 323D LN
2459350
HOSE
320D, 323D L, 323D LN
320D, 323D L, 323D LN
2459196
HOSE
323D L, 323D LN
323D L, 323D LN
2459195
HOSE
323D L, 323D LN
323D L, 323D LN
2666152
HOSE-AIR
323D L, 323D LN
323D L, 323D LN
2459194
HOSE-RADIATOR
320D L, 320D LN, 323D L, 323D LN, 323D SA
320D L, 320D LN, 323D L, 323D LN, 323D SA