2501127 HOSE AS Caterpillar parts 14H HOSE
Rating:
Alternative (cross code) number:
CA2501127
250-1127
2501127
CA2501127
250-1127
2501127

Buy HOSE AS 2501127 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,
Compatible equipment models: 2501127:
MOTOR GRADER 14H
Caterpillar
Information:
10. Remove six screws (1) and remove the head from the housing.11. Remove bearing cone (7) and spacer (2). Replace spacer with one of required thickness to provide proper preload.Adjustment of Swashplate Bearings
1. Install shaft assembly into housing.2. Place housing (5) on a flat surface with the mounting flange down.3. Install spring (11) and seat (10) in the housing.4. Install yoke (4) into the housing.5. Assemble bearing cones (13) on each end of yoke and insert bearing cups (14).6. Install bearing spacer (15) on one end.7. Install O-ring seal (17) into the groove.8. Install 0.25 mm (.010 in) shim under cover and install 4 screws (16). Tighten screws to a torque of ... 20 N m (175 lb in).9. Place the housing on its side so that the bearing bore is up. Install the bearing spacer and rotate the yoke back and forth to seat the bearings. With the spacer firmly against the bearing, use a depth micrometer and measure the difference in height between the bearing spacer and the housing. Measure in two places, 180 degrees apart, to obtain an average reading. A 0.20 0.025 mm (.008 .001 in) preload is required on the bearings. Calculate the necessary shims to provide this preload as follows: If the calculated shim thickness is greater than 0.51 mm (.020 in), another shim must be added to the opposite side of the yoke to reduce the total shim thickness to less than 0.51 mm (.020 in). Shim thickness at either cover must not exceed 0.51 mm (.020 in). This is necessary to ensure proper O-ring compression and prevent seal leakage.10. Install the correct shims and cross torque the cover screws (16) to 20 N m (175 lb in). Yoke (4) is stiff but should be free enough to be moved by hand. The tightness indicates the bearings are preloaded. If the yoke can not be moved by hand, the preload is too great. Repeat the preload adjustment.126-1184 (35 GPM)
Rotation is counterclockwise when seen from drive end.Type of pump: Variable Piston PumpFor test use SAE 10W oil at 65°C (150°F). Test at Full SpeedOutput ... 133 liter/min (35 U.S. gpm)At a pressure of ... 690 kPa (100 psi)With pump at ... 2389 rpmWith engine at ... 2100 rpmOutput ... 125 liter/min (33 U.S. gpm)At a pressure of ... 6900 kPa (1000 psi)With Pump at ... 2389 rpmWith engine at ... 2100 rpm Test at Half SpeedOutput ... 65 liter/min (17 U.S. gpm)At a pressure of ... 690 kPa (100 psi)With pump at ... 1195 rpmWith engine at ... 1050 rpmOutput ... 61 liter/min (16 U.S. gpm)At a pressure of ... 6900 kPa (1000 psi)With pump at ... 1195 rpmWith engine at ... 1050 rpm (3) Put 9S-3263 Thread Lock on threads and tighten rod to a torque of ... 79 4 N m (58 3 lb ft)(4) 6E-6579 Spring: First
1. Install shaft assembly into housing.2. Place housing (5) on a flat surface with the mounting flange down.3. Install spring (11) and seat (10) in the housing.4. Install yoke (4) into the housing.5. Assemble bearing cones (13) on each end of yoke and insert bearing cups (14).6. Install bearing spacer (15) on one end.7. Install O-ring seal (17) into the groove.8. Install 0.25 mm (.010 in) shim under cover and install 4 screws (16). Tighten screws to a torque of ... 20 N m (175 lb in).9. Place the housing on its side so that the bearing bore is up. Install the bearing spacer and rotate the yoke back and forth to seat the bearings. With the spacer firmly against the bearing, use a depth micrometer and measure the difference in height between the bearing spacer and the housing. Measure in two places, 180 degrees apart, to obtain an average reading. A 0.20 0.025 mm (.008 .001 in) preload is required on the bearings. Calculate the necessary shims to provide this preload as follows: If the calculated shim thickness is greater than 0.51 mm (.020 in), another shim must be added to the opposite side of the yoke to reduce the total shim thickness to less than 0.51 mm (.020 in). Shim thickness at either cover must not exceed 0.51 mm (.020 in). This is necessary to ensure proper O-ring compression and prevent seal leakage.10. Install the correct shims and cross torque the cover screws (16) to 20 N m (175 lb in). Yoke (4) is stiff but should be free enough to be moved by hand. The tightness indicates the bearings are preloaded. If the yoke can not be moved by hand, the preload is too great. Repeat the preload adjustment.126-1184 (35 GPM)
Rotation is counterclockwise when seen from drive end.Type of pump: Variable Piston PumpFor test use SAE 10W oil at 65°C (150°F). Test at Full SpeedOutput ... 133 liter/min (35 U.S. gpm)At a pressure of ... 690 kPa (100 psi)With pump at ... 2389 rpmWith engine at ... 2100 rpmOutput ... 125 liter/min (33 U.S. gpm)At a pressure of ... 6900 kPa (1000 psi)With Pump at ... 2389 rpmWith engine at ... 2100 rpm Test at Half SpeedOutput ... 65 liter/min (17 U.S. gpm)At a pressure of ... 690 kPa (100 psi)With pump at ... 1195 rpmWith engine at ... 1050 rpmOutput ... 61 liter/min (16 U.S. gpm)At a pressure of ... 6900 kPa (1000 psi)With pump at ... 1195 rpmWith engine at ... 1050 rpm (3) Put 9S-3263 Thread Lock on threads and tighten rod to a torque of ... 79 4 N m (58 3 lb ft)(4) 6E-6579 Spring: First
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
5P1262
HOSE
120B, 120G, 120H, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 130G, 135H, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163...
120B, 120G, 120H, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 130G, 135H, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163...
1316645
HOSE
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16M, 215B, 235B, 235D, 3176C, 3196, 330, 330 L...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16M, 215B, 235B, 235D, 3176C, 3196, 330, 330 L...
1165416
HOSE AS
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 65E, 725, 730, 75D, 75E, 834G, 836G, 85D, 85E, 95E, 988G, C-10, C-12, C12, CPT372, D7R II, MTC835, SBF214, SUF557
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 65E, 725, 730, 75D, 75E, 834G, 836G, 85D, 85E, 95E, 988G, C-10, C-12, C12, CPT372, D7R II, MTC835, SBF214, SUF557
1165418
HOSE AS
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 65E, 725, 730, 75D, 75E, 814F, 815F, 816F, 85D, 85E, 95E, C-10, C-12, C12, CPT372, SBF214,...
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 65E, 725, 730, 75D, 75E, 814F, 815F, 816F, 85D, 85E, 95E, C-10, C-12, C12, CPT372, SBF214,...
5P6412
HOSE
1090, 1190, 1190T, 1290T, 1390, 14H, 14H NA, 153, 16H, 16H NA, 2290, 2390, 2391, 2491, 2590, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 511, 521, 522, 532, 541, 541 2, 551, 552, 55...
1090, 1190, 1190T, 1290T, 1390, 14H, 14H NA, 153, 16H, 16H NA, 2290, 2390, 2391, 2491, 2590, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 511, 521, 522, 532, 541, 541 2, 551, 552, 55...
1901669
HOSE AS
120H, 120M, 12H, 12M, 135H, 140H, 140K, 140M, 143H, 14H, 160H, 160K, 160M, 163H, 16H, 16M, 301.6C, 302.5, 302.5C, 303.5, 304.5, 3304B, 3306, 3306B, 3406C, 3406E, 3408E, 3412, 3412C, 3412E, 350, 3508, ...
120H, 120M, 12H, 12M, 135H, 140H, 140K, 140M, 143H, 14H, 160H, 160K, 160M, 163H, 16H, 16M, 301.6C, 302.5, 302.5C, 303.5, 304.5, 3304B, 3306, 3306B, 3406C, 3406E, 3408E, 3412, 3412C, 3412E, 350, 3508, ...
9Y1116
HOSE AS
140H, 143H, 14H, 160H, 163H, 16H, 3176, 3176B, 3176C, 3196, 3406E, C-10, C-12, CPT372, SBF214, SUF557
140H, 143H, 14H, 160H, 163H, 16H, 3176, 3176B, 3176C, 3196, 3406E, C-10, C-12, CPT372, SBF214, SUF557
5K7577
HOSE ASSEM. .46 m(18 in.)
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
6J7929
HOSE AS
120G, 14H, 14H NA, 16H, 16H NA, 637E, 657B, 768B, 769, 772, 773, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793, 793B
120G, 14H, 14H NA, 16H, 16H NA, 637E, 657B, 768B, 769, 772, 773, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793, 793B
1129434
HOSE AS
14H, 16H, 914G, AP-655C, D7R, D7R II, IT14G, IT14G2
14H, 16H, 914G, AP-655C, D7R, D7R II, IT14G, IT14G2
3D8942
HOSE ASSEMBLY --GOVERNOR OVERRIDE VALVE TO COMPRESSOR GOVERNOR
120G, 14H, 14H NA, 16H, 16H NA, 621, 623, 627, 637D, 641, 641B, 651, 657, 657B, 666, 666B, 768B, 772, 776, 777
120G, 14H, 14H NA, 16H, 16H NA, 621, 623, 627, 637D, 641, 641B, 651, 657, 657B, 666, 666B, 768B, 772, 776, 777
8W3183
HOSE AS
14H, 16H, 769D, 771D, 789
14H, 16H, 769D, 771D, 789
1800368
HOSE AS
14H, 14M, M325B
14H, 14M, M325B
2501133
HOSE AS
14H, 16H
14H, 16H
1862784
HOSE AS
14H, 16H
14H, 16H
2474971
HOSE AS
14H
14H
1862863
HOSE AS
14H, 16H
14H, 16H
1858649
HOSE AS
14H
14H
2060483
HOSE AS
16H
16H
2060482
HOSE AS
16H
16H
2052347
HOSE AS
16H
16H
1989872
HOSE AS
14H
14H
1887494
HOSE AS
14H
14H
1887493
HOSE AS
14H
14H