2699928 HOSE AS Caterpillar parts
330D L, 330D LN
Rating:
Alternative (cross code) number:
CA2699928
269-9928
2699928
CA2699928
269-9928
2699928
EXCAVATOR,
Number on catalog scheme:
12
For full view, you need register
Information:
Illustration 1 g01353769
Connections of the ripper position sensor
This diagnostic code is recorded when the Machine ECM determines that the voltage for the ripper position sensor is too low or shorted low. The ripper position sensor is a pulse width modulated sensor.The possible causes for this diagnostic code are listed:
The harness between the ECM and the sensor has a short to ground.
The sensor has failed.
The + battery circuit has an open.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0880 FMI 04 is active before performing this procedure.Use a digital multimeter for the measurements in the procedure.System Response:The ripper function will be disabled until the diagnostic code is cleared. The tilt lever position sensor must be centered.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the sensor from the machine harness. Expected Result:The diagnostic code remains active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code is no longer active. The sensor has failed.Repair: Replace the sensor. See Testing and Adjusting, KENR5177, "Calibration" for more information. Verify that the new sensor corrects the problem.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the J1 machine harness connector, measure the resistance from contact J2-48 (wire E414-PU(Purple)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:The resistance is greater than 5000 ohms for each measurement.Results:
OK - The resistance is greater than 5000 ohms for each measurement. The ECM may have failed.Repair: The ECM may have failed. This is unlikely. Prior to replacing an ECM, contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, see Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance is less than 5000 ohms for one or more of the measurements.Repair: The machine harness has failed. There is a short in the machine harness between the signal circuit and ground. Repair the machine harness or replace the machine harness.STOP
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 3126, 3126B, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL...
307C, 308C, 311D LRR, 311F LRR, 312C, 312C L, 314D CR, 314D LCR, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D FM, 320D LRR, 320D RR, 32...
311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320B, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2 L, 321C, 321D LCR, 322, 322 FM L, 322 LN, 322B...
308C, 311C, 311D LRR, 311F LRR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 318C, 319C, 320C, 320D, 320E L, 320E LN, 321C, 321D LCR, 322C, 322C FM, 323E L, 325 L, 325B, 325C, 325C FM, 325D L, 33...
318C, 319C, 320B, 320C, 320D FM RR, 320D L, 320D LN, 320D LRR, 320D RR, 320E LRR, 320E RR, 321C, 322B LN, 322C, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D L, 325B L, 325C, 325D, 325D L, 328D LCR, 3...
312E, 312E L, 314E CR, 314E LCR, 315D L, 316E L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D L...
320B, 320C, 320C FM, 320D, 320D L, 320D LRR, 320D RR, 321C, 322B, 322C, 322C FM, 323D L, 325B, 325B L, 325C, 325C FM, 330C FM, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, ...
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 3...
324D, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 568 FM LL
325C, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2023927
HOSE AS
330D LN, 330D MH, M330D
330D LN, 330D MH, M330D
2956684
HOSE AS
330D L, 330D LN, 336D L
330D L, 330D LN, 336D L
2956675
HOSE AS
330D L, 330D LN, 336D L
330D L, 330D LN, 336D L
2956646
HOSE AS
330D L, 330D LN, 336D L
330D L, 330D LN, 336D L
2956553
HOSE AS
330D L, 330D LN, 336D L
330D L, 330D LN, 336D L
2956546
HOSE AS
330D L, 330D LN, 336D L
330D L, 330D LN, 336D L
2834255
HOSE AS
330D MH
330D MH
2834254
HOSE AS
330D MH
330D MH
2745225
HOSE AS
325D MH, 330D MH, M330D
325D MH, 330D MH, M330D
2795686
HOSE AS
330D MH, M330D
330D MH, M330D
2746072
HOSE AS
325D MH, 330D MH, M325D L MH, M325D MH, M330D
325D MH, 330D MH, M325D L MH, M325D MH, M330D
2661029
HOSE AS
330D L, 330D LN, 336D L, 336D LN
330D L, 330D LN, 336D L, 336D LN