AVSPARE.COM
parts catalog

HOSE AS 2809482 - Caterpillar



2809482 HOSE AS Caterpillar parts HOSE
Rating:
16
Alternative (cross code) number:
CA2809482
280-9482
2809482
Caterpillar 2809482 HOSE AS

Buy HOSE AS 2809482 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

1-6V4801 Dressing Stone, 2-6V4803 Thrust Bearing, (Part of 6V4804 Handle Assembly) 3-6V4804 Handle Assembly [including 6V4803 Thrust Bearing (2)], 4-6V4192 Shaft Assembly [not including tee handle (A)], 5-6V4802 Grinding Wheel, 6-6V4191 Wedge Plate Assembly, 7-6V4197 Grinder Base, 8-6V4193 Extractor (.875"-1.375"-1.875"), 9-6V4194 Extractor (1.00"-1.500"-2.00"), 10-6V4195 Extractor (1.125"-1.625"-2.125"), 11-6V4196 Extractor (1.250"-1.750"-2.250"), 12-6V4198 Grinder Group, 13-6V4199 Lifting Bracket. A-Tee Handle (not available for service).Important Information
In the procedure for valve seat insert removal given in this instruction, a grinder and grinding wheel are used to grind a groove around the inside of each insert. The extractor then fits in this groove. For 3200 and 3400 Series Engine cylinder heads (3400 shown) check for clearance at location (A), under each valve seat insert (1). If there is clearance enough for installation and use of an extractor, it will not be necessary to grind the groove in the valve seat insert. For removal of valve seat inserts that have an inside diameter smaller than the 1.250" (31.8) diameter of grinding wheel (2), it will be necessary to use a 6V4801 Dressing Stone (3) to decrease the grinding wheel diameter to the size needed. Use 6V4801 Dressing Stone (3) to keep a sharp edge on each grinding wheel. When dressing a worn grinding wheel, make the edge thickness of the wheel a little more than the thickness of lips (B) on the extractors.All Caterpillar Cylinder Heads Except D343, G343, 1693 And 5.4" (137) Bore 90° Vee Engines
(1) Measure from bottom surface (A) of the cylinder head, to a point approximately .060" (1.5) below any angular face (B) on the valve seat insert. (2) Put 6V4197 Grinder Base (1) on 6V4198 Grinder (2). Install a 6V4802 Grinding Wheel (3) on grinder (2), then adjust the position of base (1) on grinder (2) as shown, to set the depth of cut for grinding wheel (3) according to the measurement found in step 1. Tighten bolt (4) to keep base (1) in position on grinder (2). (3) Use the grinder assembly as shown to make a groove (C), all the way around the inside diameter of each valve seat insert (5) that is to be removed. Make groove (C) approximately .030" (0.76) deep. (4) Find the extractor (6) that has the largest diameter step (D), (E) or (F) that will fit the inside diameter of the valve seat insert to be removed. Install that extractor on 6V4192 Shaft Assembly (7). (5) Put the tool assembly in the valve seat insert so that necessary step, (D), (E) or (F) of the extractor is in alignment with groove (C) (see step 3). Turn


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.