AVSPARE.COM
parts catalog

HOSE AS 2809513 - Caterpillar



2809513 HOSE AS Caterpillar parts HOSE
Rating:
76
Alternative (cross code) number:
CA2809513
280-9513
2809513
Caterpillar 2809513 HOSE AS

Buy HOSE AS 2809513 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

All 3200 Series Dina Engines
These engines use two different types of fuel injection nozzles, so different parts will be needed. Because the engine lifting eye bracket mounting holes in the cylinder head are different sizes, some rework and extra parts may be needed. (1) The two types of fuel injection nozzles used on 3200 Series DINA engines are type A and B. The fuel enters from the side in the type A nozzle, and enters from the end in the type B nozzle.(2) For engines with type A nozzles, the nozzles must be installed in the cylinder head using the new 1W2459 Fuel Nozzle Clamp Assemblies provided. For engines with type B nozzles, use the former nozzle clamps. The mounting holes in the cylinder head at location (C), used for a lifting eye bracket (or for other brackets), may be a different size than the original head; therefore rework and extra parts may be needed. Cylinder heads on earlier engines had bracket mounting holes with 3/8"-16-2B threads. Later cylinder heads had bracket mounting holes with 1/2"-13-2B threads.(3) If a cylinder head of the earlier type is replacing a later cylinder head, the replacement cylinder head will have 3/8"-16-2B threads in the mounting holes. Install the bracket with S1594 Bolts and 5M2894 Washers.(4) If a cylinder head of the later type is replacing an earlier cylinder head, the holes in the lifting eye bracket (or other brackets) must be enlarged to 13.0 mm Ø (0.53" Ø). Use 6H1717 Bolts and 5P8245 Washers to install the bracket on the replacement cylinder head.3208 Dina Engines
(1) If the cylinder head is to be used on the left side of the engine, install a 9L7657 Cup Plug at location (A). If the cylinder head is to be used on the right side of the engine, install a 9L7657 Cup Plug at location (B). On all cylinder heads, install a 7H3181 Hex Countersunk Head Plug at location (C). Install 5M6213 Plugs at locations (D) as necessary. Due to the different size holes in earlier and later cylinder heads, install either a 2B858 or a 5M6214 Plug in the opening at (E).
Some earlier engines had cylinder heads with different (shorter) length head bolts in locations (F). These cylinder heads can be identified by the casting part number at location (G). Former cylinder heads with a 9L9270 casting part number, used three 2B947 Bolts [57.0 mm (2.25") long]. These bolts must be replaced with three L1329 Bolts [76.0 mm (3.00") long], which are not included in this cylinder head group.
(2) Put engine oil on the threads of the cylinder head bolts, and install the bolts in their correct positions. Tighten the bolts in the sequence and to the torque shown in the Service Manual.3204 Dina Engines
Because two different water lines groups [with different size holes in the cylinder head at location (D)] have been used on these engines, it may be necessary to obtain some additional parts. See step 1 and the illustrations for the parts


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.