HOSE-COOLANT 2S6656 - Caterpillar

Illustration 7 g03368970
Typical view (1) 293-4578 Bracket As
Illustration 8 g03368971
Typical view of the bottom of the 381-0420 Body and Canopy As , 273-3921 Body and Canopy As , 273-3922 Body and Canopy As , 306-2680 Body and Canopy As , and the 273-3920 Body and Canopy As (1) 293-4578 Bracket As
Illustration 9 g03369537
Typical view of the bottom of the 335-6000 Body and Canopy As and the 335-6002 Body and Canopy As (1) 293-4578 Bracket As
Locate five bracket assemblies (1) onto the bottom of the body and canopy assembly. Refer to the correct Illustrations above and Table 2 for the locations.As needed, remove and retain any hardware or machine components that may interfere with welding on the body and canopy assembly.Note: Ensure that bracket assemblies (1) are oriented as shown in the above Illustrations.
Table 2
Dimension     273-3921 Body and Canopy As , 306-2680 Body and Canopy As , 381-0420 Body and Canopy As , 273-3922 Body and Canopy As , and the 273-3920 Body and Canopy As (1)     335-6000 Body and Canopy As and the 335-6002 Body and Canopy As (2)    
A    
157 3 mm (6.18 0.118 inch)    
154 3 mm (6.06298 0.11811 inch)    
B    
763 3 mm (30.04 0.118 inch)    
760 3 mm (29.92120 0.11811 inch)    
C    
138 3 mm (5.43 0.118 inch)    
141 3 mm (5.55117 0.11811 inch)    
D    
109 3 mm (4.29 0.118 inch) (3)
   
59 3 mm (2.32283 0.11811 inch)    
E    
56 3 mm (2.20 0.118 inch)    
99 3 mm (3.89763 0.11811 inch)    
( 1 ) Refer to Illustration 8
( 2 ) Refer to Illustration 9
( 3 ) 59 3 mm (2.32283 0.11811 inch) for the 273-3922 Body and Canopy As Note: Refer to Special Instruction, REHS1841, "General Welding Procedures" prior to performing any welding.Note: Remove all paint, dirt, oil, debris, or other contaminants from the area to be welded prior to completing any welding.
Tack weld to bracket assemblies (1) on the body and canopy assembly.
Use an 8 mm (0.315 inch) all around fillet weld to fully secure bracket assemblies (1) to the frame.Note: All finish welds must be inspected for any defects. Note: Refer to Special Instruction, REHS1841, "General Welding Procedures" for inspection instructions.
Reinstall any hardware or machine components that were removed in Step 1.
As needed, repaint the areas.
Install the warning films. Refer to ""Warning Films"" for additional information.Warning Films
Illustration 10 g03359590
(2) 299-5775 Film (3) 299-5776 Film (4) 299-5777 Film (5) 299-5778 Film
After the welds have been inspected and painted, install one of the following warning films:
(2) 299-5775 Film
(3) 299-5776 Film
(4) 299-5777 Film
(5) 299-5778 Film Note: Films should be installed 50 to 75 mm (2 to 3 inch) from bracket assemblies (1) .Note: Customers in North America should use either