3107723 HOSE AS Caterpillar parts
D9R, D9T
Rating:
Alternative (cross code) number:
CA3107723
310-7723
3107723
CA3107723
310-7723
3107723
Weight: 0.37 pounds 0 kg.
TRACK-TYPE TRACTOR,
Information:
start by:a) remove engineb) remove flywheel housingc) remove timing gear coverd) remove pistons
TYPICAL EXAMPLE1. Turn the crankshaft until the timing mark (C) on the crankshaft gear (1) is in alignment with the timing mark (C) on camshaft gear (2).2. Make a mark on the teeth of the fuel pump drive gear and the idler gear in their engaged position at location (X). Make a mark on the engaged teeth of idler gear and camshaft gear at location (Y). This will give assistance in the correct timing of the camshaft for the fuel injection pump during crankshaft installation. 3. Fasten a hoist to the crankshaft.4. Remove the caps for the main bearings.5. Remove the crankshaft. Weight of the crankshaft is 95 kg (210 lb.).6. Remove the main bearings from the main bearing caps. Remove the crankshaft main bearings from the cylinder block. 7. Use tool (A) to remove the crankshaft gear and the oil seal wear sleeve.Install Crankshaft
Install the bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in the cylinder block and main bearing caps.
1. Clean the bearing surfaces in the cylinder block. Install the upper halves of the main bearings in the block.2. Heat the crankshaft gear to a maximum temperature of 315°C (600°F). Install the gear on the crankshaft. Fasten a hoist to the crankshaft and put the crankshaft in position in the cylinder block with all timing marks in alignment.3. Clean the bearing surfaces of the main bearing caps. Install the lower halves of the main bearings in the caps. When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances. 4. Check the main bearing clearances with Plastigage (A) as follows: a) Put a piece of Plastigage (A) in position as shown.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
Do not turn the crankshaft when Plastigage (A) is in position.b) Install the main bearing caps. Put clean engine oil on the bolt threads and the face of the washers and install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb.ft.).
Do not use an impact wrench to tighten the bolts the
TYPICAL EXAMPLE1. Turn the crankshaft until the timing mark (C) on the crankshaft gear (1) is in alignment with the timing mark (C) on camshaft gear (2).2. Make a mark on the teeth of the fuel pump drive gear and the idler gear in their engaged position at location (X). Make a mark on the engaged teeth of idler gear and camshaft gear at location (Y). This will give assistance in the correct timing of the camshaft for the fuel injection pump during crankshaft installation. 3. Fasten a hoist to the crankshaft.4. Remove the caps for the main bearings.5. Remove the crankshaft. Weight of the crankshaft is 95 kg (210 lb.).6. Remove the main bearings from the main bearing caps. Remove the crankshaft main bearings from the cylinder block. 7. Use tool (A) to remove the crankshaft gear and the oil seal wear sleeve.Install Crankshaft
Install the bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in the cylinder block and main bearing caps.
1. Clean the bearing surfaces in the cylinder block. Install the upper halves of the main bearings in the block.2. Heat the crankshaft gear to a maximum temperature of 315°C (600°F). Install the gear on the crankshaft. Fasten a hoist to the crankshaft and put the crankshaft in position in the cylinder block with all timing marks in alignment.3. Clean the bearing surfaces of the main bearing caps. Install the lower halves of the main bearings in the caps. When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances. 4. Check the main bearing clearances with Plastigage (A) as follows: a) Put a piece of Plastigage (A) in position as shown.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
Do not turn the crankshaft when Plastigage (A) is in position.b) Install the main bearing caps. Put clean engine oil on the bolt threads and the face of the washers and install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb.ft.).
Do not use an impact wrench to tighten the bolts the
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
5P1262
HOSE
120B, 120G, 120H, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 130G, 135H, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163...
120B, 120G, 120H, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 130G, 135H, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163...
5P1259
HOSE
12M, 140G, 140M, 245B, 24M, 3114, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3406, 3406B, 3406E, 3408, 3408B, 3412, 3412C, 3412D, 3412E, 446, 515, 518, 518C, 525, 554, 574, 594H, ...
12M, 140G, 140M, 245B, 24M, 3114, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3406, 3406B, 3406E, 3408, 3408B, 3412, 3412C, 3412D, 3412E, 446, 515, 518, 518C, 525, 554, 574, 594H, ...
6N3169
HOSE AS
1673C, 3304, 3306, 3406C, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3512, 3516, 589, 631D, 631E, 631G, 637D, 637E, 637G, 651E, 657E, 769C, 771C, 773B, 775B, 834B, 988B, 988F, 990, 992C, 992...
1673C, 3304, 3306, 3406C, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3512, 3516, 589, 631D, 631E, 631G, 637D, 637E, 637G, 651E, 657E, 769C, 771C, 773B, 775B, 834B, 988B, 988F, 990, 992C, 992...
2423360
HOSE
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 3126, 3126B, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL...
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 3126, 3126B, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL...
5P1471
HOSE
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 245B, 24M, 3176B, 3176C, 3196, 330D, 3406, 3406B, 3406C, 3408, 3412, 5110B, 5130, 5130B, 583T, 587R, 587T, 589,...
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 245B, 24M, 3176B, 3176C, 3196, 330D, 3406, 3406B, 3406C, 3408, 3412, 5110B, 5130, 5130B, 583T, 587R, 587T, 589,...
3718115
HOSE
120M, 12M, 140M, 14M, 160M, 3306B, 572R II, 621F, 621G, 623E, 623G, 627F, 627G, 735, 773B, 773D, 775B, 824G, 825G, 826G, 980C, 980F, 980G, D10N, D10R, D10T, D7R II, D8N, D8R, D8R II, D9N, D9R
120M, 12M, 140M, 14M, 160M, 3306B, 572R II, 621F, 621G, 623E, 623G, 627F, 627G, 735, 773B, 773D, 775B, 824G, 825G, 826G, 980C, 980F, 980G, D10N, D10R, D10T, D7R II, D8N, D8R, D8R II, D9N, D9R
7T9105
HOSE AS
589, 988F, 988F II, D10R, D4K XL, D5K LGP, D9R
589, 988F, 988F II, D10R, D4K XL, D5K LGP, D9R
1234080
HOSE AS
D9R
D9R
1Q1372
HOSE AS
D9R
D9R
1117745
HOSE AS
D9R, D9T
D9R, D9T
1188138
HOSE AS
D9R, D9T
D9R, D9T
8E9427
HOSE AS
D9N, D9R, D9T
D9N, D9R, D9T
2678670
HOSE AS
D9R
D9R
2678668
HOSE AS
D9R
D9R
4443513
HOSE AS
D8T
D8T
4443512
HOSE AS
D8T
D8T
4239397
HOSE AS
D8T
D8T
4239398
HOSE AS
D8T
D8T
3738705
HOSE AS
D9R
D9R
3738703
HOSE AS
D9R
D9R
3738702
HOSE AS
D9R
D9R
3111516
HOSE AS
D9R
D9R
3107725
HOSE AS
D9R, D9T
D9R, D9T
3107724
HOSE AS
D9R
D9R