3200051 HOSE AS Caterpillar parts
314D LCR
Rating:
Alternative (cross code) number:
CA3200051
320-0051
3200051
CA3200051
320-0051
3200051
EXCAVATOR,
Compatible equipment models: 3200051:
Number on catalog scheme:
11
For full view, you need register
Information:
6. Remove thrust bearings (7) from the rear main bearing. 7. Install tooling (B) on crankshaft (8) as shown and fasten a hoist to it. Lift the crankshaft straight up from the cylinder block. The weight of the crankshaft for 3304 Engines is 65 kg (143 lb.). The weight of the crankshaft for 3306 Engines is 95 kg (210 lb.). 8. Use tooling (C) and remove crankshaft gear (1) from the crankshaft.
If the bearings are to be removed, put identification marks on them as to their location for installation purposes.
9. If necessary, remove the main bearings from the cylinder block and main bearing caps. If necessary, remove the connecting rod bearings from the connecting rods and connecting rod caps.Install Crankshaft
1. Put the engine in position on tooling (A). If the crankshaft journals and bores for the block and rods were measured at disassembly and found to be within specifications, no further checks are necessary. However, If the serviceman still wants to measure the bearing clearances, Plastigage is recommended. Lead wire, shim stock or use of a dial bore gauge can damage the bearing surface.The serviceman must be very careful to use Plastigage correctly. The following points must be remembered:... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap, but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances, see Engine Bearings
If the bearings are to be removed, put identification marks on them as to their location for installation purposes.
9. If necessary, remove the main bearings from the cylinder block and main bearing caps. If necessary, remove the connecting rod bearings from the connecting rods and connecting rod caps.Install Crankshaft
1. Put the engine in position on tooling (A). If the crankshaft journals and bores for the block and rods were measured at disassembly and found to be within specifications, no further checks are necessary. However, If the serviceman still wants to measure the bearing clearances, Plastigage is recommended. Lead wire, shim stock or use of a dial bore gauge can damage the bearing surface.The serviceman must be very careful to use Plastigage correctly. The following points must be remembered:... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap, but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances, see Engine Bearings
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
307B, 307C, 308C, 311D LRR, 311F LRR, 312C L, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
307C, 311F LRR, 312C, 312C L, 312D, 312E, 312E L, 314D CR, 314D LCR, 315D L, 318C, 319C, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM RR, 320D2 L, 321C, 322B, 322B L, 322B LN, 322C, 322C FM, 325,...
307C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 32...
307C, 311C, 311D LRR, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320C, 320D, 3...
307C, 308C, 311D LRR, 311F LRR, 312C, 312C L, 314D CR, 314D LCR, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D FM, 320D LRR, 320D RR, 32...
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LN, 320D...
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
308C, 311C, 311F LRR, 312C, 312C L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D FM RR,...
308C, 312C, 312C L, 312D, 312D L, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2...
308C, 311C, 311D LRR, 311F LRR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 318C, 319C, 320C, 320D, 320E L, 320E LN, 321C, 321D LCR, 322C, 322C FM, 323E L, 325 L, 325B, 325C, 325C FM, 325D L, 33...
3230729
HOSE AS
314D LCR
314D LCR
3230726
HOSE AS
314D LCR
314D LCR
3689412
HOSE AS
314D LCR, 325D L
314D LCR, 325D L
3029675
HOSE AS
314D LCR
314D LCR
3075113
HOSE AS
314D LCR
314D LCR
3200098
HOSE AS
314D LCR
314D LCR
2895465
HOSE AS
314D LCR
314D LCR
2895462
HOSE AS
314D LCR
314D LCR
2895458
HOSE AS
314D LCR
314D LCR
2895454
HOSE AS
314D LCR
314D LCR
3075241
HOSE AS
314D LCR
314D LCR
2967384
HOSE AS
314D LCR
314D LCR