AVSPARE.COM
parts catalog

HOSE AS 3237425 - Caterpillar



3237425 HOSE AS Caterpillar parts HOSE
Rating:
86
Alternative (cross code) number:
CA3237425
323-7425
3237425
Caterpillar 3237425 HOSE AS

Buy HOSE AS 3237425 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Guidelines
Use a 1U-5804 Crimp Tool (12-GA TO 18-GA) to service Deutsch HD and DT connectors. Never solder the terminals onto the wires.
Use a 147-6456 Wedge Removal Tool to remove wedges from DT connectors. Never use a screwdriver to pry a wedge from a connector.
Use a breakout harness for a voltmeter probe or a test light. Never break the wire insulation to access a circuit for measurements.
If a wire is cut, install a new terminal for the repair.Reference: Tool Operating Manual, SEHS9615, "Servicing Deutsch HD and DT Style Connectors"Some minor seal abrasion on connector seals is normal. Minor seal abrasion will not allow the entry of moisture. If moisture or corrosion is evident in the connector, the source of the moisture entry must be found and repaired. If the source of the moisture entry is not repaired, the problem will recur. Simply drying the connector will not fix the problem.Moisture can also travel to a connector through the inside of a wire. If moisture is found in a connector, thoroughly check the connector harness for damage. Also check all the remaining connectors on the harness for moisture.The plug end of the DT connector has a replaceable seal at the mating end of the connector. This seal has been improved on black connectors to help prevent slipping and to help keep moisture and dirt from entering the connector.The current seal design (2) is not interchangeable with the former design (1). The receptacle has also changed to the new colors.
Illustration 1 g01960167
(1) Former seal design
(2) Current seal design
Illustration 2 g01960176
(3) Seal for a three-pin connector (typical example)
Illustration 3 g02732798
(4) Locking wedge for three-pin connectorTroubleshooting Steps
Table 1
Troubleshooting Steps Values Results
1. Check Harnesses
A. Visually inspect the wiring.
B. Visually inspect the connectors.
C. Visually inspect the seals.
Harnesses:
* Routing allows the wires to enter each connector face at a perpendicular angle.
* No insulation nicks.
Connectors:
* Are properly mated.
* Have no moisture.
Seals:
* Seals are sealing.
* No seals are missing.
OK - The harness is OK.
Go to Step 2.
Not OK - The harness is not OK.
Repair:
A. Repair or replace the harness.
B. Verify that the repair corrected the problem.
STOP.
2. Check Fasteners And Wires
A. Visually inspect the fasteners.
B. Visually inspect the wiring.
Fasteners:
* Fasteners are not overtightened.
Wiring:
* Is secure.
* Is not compressed.
* Has no abrasion.
* Has no nicks.
* Has no cuts.
* Has no exposed insulation.
* Has no rubbing against the chassis or a sharp point.
OK - The harness is OK.
Go to Step 3.
Not OK - The harness is not OK.
Repair:
A. Repair or replace the harness.
B. Verify that the repair corrected the problem.
STOP.
3. Inspect Connector Terminal And Locking Wedge
A. Visually inspect the terminals.
B. Visually inspect the locking wedges. See Figure 3.
Terminals are:
* Properly aligned.
* Undamaged.
* Properly located in the connector.
* Properly crimped in the terminal.
Locking wedges are:
* Properly installed.
OK - The terminals are OK.
Go to Step 4.
Not OK - The terminals are not OK.
Repair:
A. Repair and/or replace the terminals.
B. Verify that the repair corrected the problem.
STOP.
4. Check Wire Terminal Connection
A. Perform a pull test on each wire.
Connections:
* Withstand 45 N (10 lb) of tension.
OK -


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.