3401804 HOSE-REDUCER Caterpillar parts
525C, 535C, 545C
Rating:
Alternative (cross code) number:
CA3401804
340-1804
3401804
CA3401804
340-1804
3401804
Weight: 4 pounds 2 kg.
WHEEL SKIDDER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$15.10
18 Aug 2023
Amazon.com
Sunsong 3401804 Power Steering Pressure Line Hose Assembly
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
$14.72
04 Apr 2023
Amazon.com
Sunsong 3401804 Power Steering Pressure Line Hose Assembly
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
$19.95
12 Aug 2022
US: Auto Barn
Sunsong 3401804 Power Steering Pressure Line Hose Assembly
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
Sunsong Pressure Hoses exceed original equipment performance standards (SAE J2050) with a Max working pressure of 1, 500 psi a burst pressure rating of 8, 700 psi and a tensile strength of 1, 600 lb. This provides exceptional durability and long life || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, switch ports, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Every hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new Hose || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 310 degrees Fahrenheit, exceeding original equipment requirements
Number on catalog scheme:
4
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 1 g01369129
Typical example
If the ring gear was removed, follow Steps 1.a through 1.c in order to install ring gear (3) to flywheel (2).
Identify the orientation of the new ring gear in order to install the ring gear correctly onto the flywheel.Note: The chamfered side of gear teeth (Y) must face toward the starting motor when the flywheel is installed. This will ensure the correct engagement of the starting motor.
Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (2) .
Illustration 2 g01335288
Typical example
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install".
Ensure that the dowels are installed to the crankshaft. Install Tooling (A) to positions (X) in the crankshaft.
Install a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 23 kg (50 lb).
Align flywheel (2) with Tooling (A). Install the flywheel to the crankshaft.Note: Ensure the correct orientation of the flywheel on the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (A) and install the two remaining bolts (1) .
Remove the lifting device from the flywheel.
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 83 N m (61 lb ft).
Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting, "Flywheel - Inspect".End By: Install the starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 1 g01369129
Typical example
If the ring gear was removed, follow Steps 1.a through 1.c in order to install ring gear (3) to flywheel (2).
Identify the orientation of the new ring gear in order to install the ring gear correctly onto the flywheel.Note: The chamfered side of gear teeth (Y) must face toward the starting motor when the flywheel is installed. This will ensure the correct engagement of the starting motor.
Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (2) .
Illustration 2 g01335288
Typical example
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install".
Ensure that the dowels are installed to the crankshaft. Install Tooling (A) to positions (X) in the crankshaft.
Install a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 23 kg (50 lb).
Align flywheel (2) with Tooling (A). Install the flywheel to the crankshaft.Note: Ensure the correct orientation of the flywheel on the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (A) and install the two remaining bolts (1) .
Remove the lifting device from the flywheel.
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 83 N m (61 lb ft).
Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting, "Flywheel - Inspect".End By: Install the starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
16M, 3176B, 3176C, 3196, 3406E, 3456, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 385C, 525C, 535C, 545C, 621B, 621G, 621H, 621K, 623G, 623H, 623K ...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16H NA, 225D, 231D, 236D, 242D, 2...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3,...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K...
3116, 3126, 3208, 3306B, 3508, 3508C, 3512, 3512B, 3516, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 515, 525, 525B, 525C, 535B, 535C, 545, 545C, D379, D379B, D7G, ...
3512B, 3512C, 3516B, 3516C, 515, 525, 525C, 535C, 545C, 924G, 924GZ, 963, AD40, AD45B, AD55, AD55B, AD60, AE40, RM-500
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 3126, 3126B, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL...
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3114, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D...
515, 525, 525B, 525C, 535B, 535C, 545, 545C, 621, 621B, 621E, 621F, 623, 623E, 623F, 627, 627E, 627F, 631C, 631D, 633D, 637, 637D, 641, 641B, 651, 657B, 69D, 768B, 768C, 769, 769C, 769D, 771C, 771D, 7...
2997731
HOSE AS
525C, D11T
525C, D11T
2931117
HOSE AS
320D, 320D FM, 320D L, 323D L, 323D LN
320D, 320D FM, 320D L, 323D L, 323D LN
2931120
HOSE AS
320D, 320D L, 320D2 L, 323D L, 323D2 L
320D, 320D L, 320D2 L, 323D L, 323D2 L
2786886
HOSE AS
323D L, 323D LN
323D L, 323D LN
2786883
HOSE AS
323D L, 323D LN
323D L, 323D LN
2929325
HOSE AS
323D L
323D L
2827058
HOSE AS
323D L
323D L
3831288
HOSE AS
525C, 535C, 545C
525C, 535C, 545C
3916328
HOSE AS
525C, 535C, 545C
525C, 535C, 545C
2538307
HOSE AS
525C, 535C, 545C
525C, 535C, 545C
2892473
HOSE AS
545C
545C
2632596
HOSE AS
545C
545C
2902949
HOSE-REDUCER
525C, 535C, 545C
525C, 535C, 545C