3497545 HOSE Caterpillar parts
C27
Rating:
Alternative (cross code) number:
CA3497545
349-7545
3497545
CA3497545
349-7545
3497545
Weight: 5 pounds 2 kg.
GENERATOR SET,
Compatible equipment models: 3497545:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-5096     Dial Indicator Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil to the upper main bearing. Do not apply engine oil to the back side of the bearing surfaces. Install the upper main bearings in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01128041
Apply clean engine oil to the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 62 kg (137 lb). Align the identification marks on the gear train. Install crankshaft (1) in the cylinder block.
Clean the bearing surface of main bearing caps (3). Install the lower main bearings in the main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil to the lower main bearings. Do not apply engine oil to the back side of the bearing surfaces.
Install main bearing caps (3) with the part numbers toward the right hand side of the cylinder block. Ensure that the main bearing caps have numbers 1 through 7. The numbers should start at the front of the engine. Apply clean engine oil or Molylube to the bolt threads and the washers.Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this position and tighten the bolts.
Install bolts (2) for main bearing caps (3). Tighten bolts (2) to a torque of 54 7 N m (40 5 lb ft).
Turn bolts (2) for an additional 90 5 degrees (1/4 turn).
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 mm to 0.32 mm (0.003 inch to 0.013 inch).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install".
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-5096     Dial Indicator Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil to the upper main bearing. Do not apply engine oil to the back side of the bearing surfaces. Install the upper main bearings in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01128041
Apply clean engine oil to the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 62 kg (137 lb). Align the identification marks on the gear train. Install crankshaft (1) in the cylinder block.
Clean the bearing surface of main bearing caps (3). Install the lower main bearings in the main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil to the lower main bearings. Do not apply engine oil to the back side of the bearing surfaces.
Install main bearing caps (3) with the part numbers toward the right hand side of the cylinder block. Ensure that the main bearing caps have numbers 1 through 7. The numbers should start at the front of the engine. Apply clean engine oil or Molylube to the bolt threads and the washers.Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this position and tighten the bolts.
Install bolts (2) for main bearing caps (3). Tighten bolts (2) to a torque of 54 7 N m (40 5 lb ft).
Turn bolts (2) for an additional 90 5 degrees (1/4 turn).
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 mm to 0.32 mm (0.003 inch to 0.013 inch).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install".
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
7E8630
HOSE-AIR INLET
16M, 3176B, 3176C, 3196, 3406E, 3456, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 385C, 525C, 535C, 545C, 621B, 621G, 621H, 621K, 623G, 623H, 623K ...
16M, 3176B, 3176C, 3196, 3406E, 3456, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 385C, 525C, 535C, 545C, 621B, 621G, 621H, 621K, 623G, 623H, 623K ...
6F5985
HOSE AS
3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, C27, C32, D337, D348, D349, D353C, D364, D375D, D379, D379A, D379B, D397D, D398, D398A, D...
3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, C27, C32, D337, D348, D349, D353C, D364, D375D, D379, D379A, D379B, D397D, D398, D398A, D...
2V5956
HOSE AS
215, 215B, 3126, 3126B, 3126E, 3208, 3304, 3306, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 834B, ...
215, 215B, 3126, 3126B, 3126E, 3208, 3304, 3306, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 834B, ...
7V1073
HOSE AS
225, 3408, 3408C, 3408E, 3412E, 3512, 3606, 3608, 3612, 3616, 3618, C27, C280-12, C280-16, C280-6, C280-8, C32
225, 3408, 3408C, 3408E, 3412E, 3512, 3606, 3608, 3612, 3616, 3618, C27, C280-12, C280-16, C280-6, C280-8, C32
1417143
HOSE-ELBOW
3508, 3508C, 3512, 3512B, 3512C, 3516, 3516C, 5130, 776C, 777B, 777D, 777F, 784C, 785, 785B, 785C, 785D, 789D, 797, 797B, 844H, 990H, C27, C32, CX35-P800, D10T, G3512E, G3516C, G3516E, G3516H, G3520C,...
3508, 3508C, 3512, 3512B, 3512C, 3516, 3516C, 5130, 776C, 777B, 777D, 777F, 784C, 785, 785B, 785C, 785D, 789D, 797, 797B, 844H, 990H, C27, C32, CX35-P800, D10T, G3512E, G3516C, G3516E, G3516H, G3520C,...
3N4847
HOSE AS
3116, 3126, 3208, 3406, 3408B, 3512, 3512C, 3606, 641B, 988, 992, C18, C27, C32, D379, D379B, D399, G3306, G3512, TH48-E70
3116, 3126, 3208, 3406, 3408B, 3512, 3512C, 3606, 641B, 988, 992, C18, C27, C32, D379, D379B, D399, G3306, G3512, TH48-E70
8N5991
HOSE
3412, 3512C, 3516C, 627H, 627K LRC, 773F, 775F, 776C, 777, 777B, 777F, 824K, 825K, 826K, 834K, 836K, 988K, AD55B, C27, C32, G3412, G3508, G3508B, G3512E, G3516, G3516B, G3516C, G3520C, TH48-E70
3412, 3512C, 3516C, 627H, 627K LRC, 773F, 775F, 776C, 777, 777B, 777F, 824K, 825K, 826K, 834K, 836K, 988K, AD55B, C27, C32, G3412, G3508, G3508B, G3512E, G3516, G3516B, G3516C, G3520C, TH48-E70
3117508
HOSE-WATER INLET
C27, C32, TH48-E70
C27, C32, TH48-E70
2562211
HOSE AS
834H, 836H, 988H, C15, C18, C27, C32, CX31-C15I, CX35-P800, TH35-C15I, TH48-E70
834H, 836H, 988H, C15, C18, C27, C32, CX31-C15I, CX35-P800, TH35-C15I, TH48-E70
2T3695
HOSE AS
613C II, C27, C32, TH48-E70
613C II, C27, C32, TH48-E70
1750059
HOSE AS
C27, C32, TH48-E70
C27, C32, TH48-E70
2653955
HOSE AS
C27, C32, TH48-E70
C27, C32, TH48-E70
3954047
HOSE AS-AIR
C27, C32
C27, C32
3949366
HOSE AS
C27
C27
3913036
HOSE AS
C27, C32
C27, C32
3913035
HOSE AS
C27, C32
C27, C32
3898067
HOSE-TEE
C27, C32
C27, C32
4492814
HOSE AS
C27
C27
3980693
HOSE AS
C27, C32
C27, C32
3906931
HOSE AS
C27, C32
C27, C32
3525052
HOSE AS
C27
C27
3525051
HOSE AS
C27
C27
3525050
HOSE AS
C27
C27