AVSPARE.COM
parts catalog

HOSE GP-REFUELING 3728208 - Caterpillar



3728208 HOSE GP-REFUELING Caterpillar parts HOSE
Rating:
81
Alternative (cross code) number:
CA3728208
372-8208
3728208
Caterpillar 3728208 HOSE GP-REFUELING

Buy HOSE GP-REFUELING 3728208 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
 
  For full view, you need register

Information:

Oil Supply
The self contained oil supply will improve governor life cycle by eliminating the opportunity for contamination from the engine oil. Governors on all new engines will be factory filled with oil. Replacement governors must be filled with oil before operation. In general, the same oil used in the engine will be satisfactory for use in the governor. For ambient temperature extremes, a synthetic oil is recommended.
Fill the governor with clean, noncorrosive, oxidation and rust inhibiting oil that has minimum foaming or air retention qualities, and a viscosity of 100 - 300 SUS (Saybolt Universal Seconds) at operating temperature [typically 60 - 93 degrees C (140 - 200 degrees F)]. Fill to the line on the sight glass [approximately 2.2 L (2.33 qt)]. After setup, and when the engine and governor are at operating temperature, again check the oil level and add more oil if necessary. Oil should be visible in the sight glass at all times.
Oil Viscosities
The governor will operate at temperatures near the pour point of the oil, but governor operation will be slow, and may be unstable. Do not operate the governor at a temperature less than the pour point of the oil.
Operating the governor at temperatures greater than the high limit (50 SUS), will decrease the stability of the governor, and may result in an inability to restart hot. Operating the governor at a temperature greater than the point at which the performance of the oil decreases can cause governor failure. See the Oil Viscosity Chart for temperature ranges.
The recommended governor oil change interval is 20,000 hours.
Oil Viscosity ChartSmoke Limiter
The new governor has an improved smoke limiter design to help eliminate limiter sticking. This sticking may cause the engine to have low power as the limiter would not move and would continuously limit the fuel. The new improved limiter design will also reduce the stem side to side movement. This will improve the diaphragm life.
Oil-Ring Groove
The new governors have a larger O-ring groove and seal to improve the seal between the governor and governor drive. The O-ring groove is common to the 3500 pump housing.
Illustration 1. Location of the 8C-5197 O-Ring (1) and 9Y-1588 Oil Pump (2).Adaptable To: The chart identifies the former and new governor part numbers.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
MH3022 Wheeled Excavator Material Handler FB300001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FB500001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FB700001-UP (MACHINE) POWERED BY C7.1 Engine
MH3026 Wheeled Excavator Material Handler FB900001-UP (MACHINE) POWERED BY C7.1 Engine
MH3024 Wheeled Excavator Material Handler FM400001-UP (MACHINE) POWERED BY C7.1 Engine
MH3022 Wheeled Excavator Material Handler FM200001-UP (MACHINE) POWERED BY C7.1 Engine
M314F Wheeled Excavator FB400001-UP (MACHINE) POWERED BY C4.4 Engine
M316F Wheeled Excavator FB600001-UP (MACHINE) POWERED BY C4.4 Engine
M318F Wheeled Excavator FB800001-UP (MACHINE) POWERED BY C7.1 Engine
M320F Wheeled Excavator FB200001-UP (MACHINE) POWERED BY C7.1 Engine
M322F Wheeled Excavator FBW00001-UP (MACHINE) POWERED BY C7.1 Engine
M315F Wheeled Excavator F4D00001-UP (MACHINE) POWERED BY C4.4 Engine
M317F Wheeled Excavator F6P00001-UP (MACHINE) POWERED BY C4.4 Engine
M322F Wheeled Excavator F2Z00001-UP (MACHINE) POWERED BY C7.1 Engine
M320F Wheeled Excavator F2W00001-UP (MACHINE) POWERED BY C7.1 Engine
M318F Wheeled Excavator F8B00001-UP (MACHINE) POWERED BY C7.1 Engine
M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
M316F Wheeled Excavator F6N00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.