3773331 HOSE AS Caterpillar parts
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
Rating:
Alternative (cross code) number:
CA3773331
377-3331
3773331
CA3773331
377-3331
3773331
EXCAVATOR,
Compatible equipment models: 3773331:
For full view, you need register
Information:
Momentary on, normally open contacts held closed in assemblyDistance to actuate switch (dimension [A]) ... 1.52 mm (.060 in) maximumActuating force ... 1.6 N (.36 lb)Neutralizer Switch Assembly Adjustment
The adjustment for the neutralizer switch assembly has been preset at assembly. However, the following procedure should be used if the switch assembly requires service, or adjustment is needed to match a particular application or an operator's preference. Both the neutralizer switch assembly and the stop lamp switch assembly are positioned immediately next to each other in the left pedal assembly. Both switch assemblies share the same mounting screws and therefore, both switch assemblies must be installed when making an adjustment to either switch. The neutralizer switch assembly is located toward the center of the pedal assembly.1. Disconnect receptable assembly (4) from the attached wire harness assembly (not shown).2. Connect an ohmmeter (or continuity tester) to Pin 5 and Pin 6 of receptable assembly (4). With pedal assembly (1) in the retracted position (fully released), the ohmmeter should indicate a closed (shorted) circuit condition.3. With pedal assembly (1) in the retracted position (fully released), depress the pedal assembly until dimension (A) is obtained. Minimum value for dimension (A) should equal approximately 6.0 mm (.24 in).4. The ohmmeter should now indicate an open (infinite) circuit condition, and an audible "click" should be heard which indicates the switch has been actuated. Do NOT make the mistake of only listening for the audible "click" sound because both the transmission neutralizer and stop lamp switch assemblies make the same sound, and should be set to actuate at approximately the same time.If the previous steps do not indicate an open circuit, proceed with the following steps.5. Remove plug (3), and insert a 3.18 mm (.125 in) hex wrench in screw (2).6. Rotate the wrench in one-quarter turn increments and repeat Steps 3 and 4 until the desired result is obtained. Rotating screw (2) clockwise increases the value of dimension (A). Rotating screw (2) counterclockwise decreases the value of dimension (A).7. Install plug (3).
The adjustment for the neutralizer switch assembly has been preset at assembly. However, the following procedure should be used if the switch assembly requires service, or adjustment is needed to match a particular application or an operator's preference. Both the neutralizer switch assembly and the stop lamp switch assembly are positioned immediately next to each other in the left pedal assembly. Both switch assemblies share the same mounting screws and therefore, both switch assemblies must be installed when making an adjustment to either switch. The neutralizer switch assembly is located toward the center of the pedal assembly.1. Disconnect receptable assembly (4) from the attached wire harness assembly (not shown).2. Connect an ohmmeter (or continuity tester) to Pin 5 and Pin 6 of receptable assembly (4). With pedal assembly (1) in the retracted position (fully released), the ohmmeter should indicate a closed (shorted) circuit condition.3. With pedal assembly (1) in the retracted position (fully released), depress the pedal assembly until dimension (A) is obtained. Minimum value for dimension (A) should equal approximately 6.0 mm (.24 in).4. The ohmmeter should now indicate an open (infinite) circuit condition, and an audible "click" should be heard which indicates the switch has been actuated. Do NOT make the mistake of only listening for the audible "click" sound because both the transmission neutralizer and stop lamp switch assemblies make the same sound, and should be set to actuate at approximately the same time.If the previous steps do not indicate an open circuit, proceed with the following steps.5. Remove plug (3), and insert a 3.18 mm (.125 in) hex wrench in screw (2).6. Rotate the wrench in one-quarter turn increments and repeat Steps 3 and 4 until the desired result is obtained. Rotating screw (2) clockwise increases the value of dimension (A). Rotating screw (2) counterclockwise decreases the value of dimension (A).7. Install plug (3).
Parts hose Caterpillar catalog:
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
311B, 315B, 315C, 315D L, 316E L, 318B, 318C, 318D2 L, 318E L, 320, 320 L, 320B, 320B FM LL, 320C, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320N, 321B, 321D LCR, 323D L, 323D LN, 323D SA, ...
307B, 307C, 308C, 311D LRR, 311F LRR, 312C L, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
307C, 311C, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320 L, 320B, 320C, 320D, 320D FM, 320D GC, 320D L, 32...
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LN, 320D...
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
308C, 312C, 312C L, 312D, 314C, 315C, 315D L, 318D2 L, 319D L, 320 L, 320B, 320C, 320D, 320D L, 320D LRR, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322B, 322B L, 322B LN, 322C FM, 323E L, 324D, 324D F...
308C, 312C, 312C L, 312D, 312D L, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2...
315C, 318C, 319C, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 322C, 322C FM, 323D L, 323D LN, 323D2 L, 325C, 325C FM, 325C L, 350, 385B
315D L, 316E L, 318D2 L, 318E L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 324D LN, 325D, 325D L, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336...
319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 321D LCR, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324E, 325C FM, 330C FM
3773328
HOSE AS
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3960208
HOSE AS
320D L, 323D L
320D L, 323D L
3794428
HOSE
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
3794424
HOSE
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
3794423
HOSE AS
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
3794411
HOSE AS
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
3729410
HOSE AS-REFRIGERANT
320D2 L, 323D L, 323D2 L
320D2 L, 323D L, 323D2 L
3729409
HOSE AS-REFRIGERANT
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3729407
HOSE AS-REFRIGERANT
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L
3773294
HOSE AS
320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3766342
HOSE AS
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3773291
HOSE AS
320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L