3834298 HOSE AS Caterpillar parts
966M, 966M XE, 972M, 972M XE
Rating:
Alternative (cross code) number:
CA3834298
383-4298
3834298
CA3834298
383-4298
3834298
WHEEL LOADER,
Information:
Removal Procedure
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00548374
Typical example
Illustration 2 g00606467
Remove valve assembly (1) from piston cooling jet (2) .
Remove piston cooling jet (2) from the cylinder block.Note: The engine crankshaft may be rotated in order to access the piston cooling jet.Note: Ensure that the ball moves freely within the valve assembly of the piston cooling jet. Check that the tube of the piston cooling jet is not damaged.
Inspect the condition of hollow dowel (3). If the hollow dowel is damaged, use a new part for replacement.Note: Hollow dowel (3) is used to locate the piston cooling jet.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00548374
Typical example
Illustration 4 g00606467
Install piston cooling jet (2) in the cylinder block.Note: Ensure that piston cooling jet (2) is properly located on hollow dowel (3). Refer to the Specifications Manual, "Piston Cooling Jet" topic for the correct procedure for the alignment of the piston cooling jet.
Install valve assembly (1) into piston cooling jet (2). Tighten the banjo bolt of valve assembly (1) to a torque of 27 N m (20 lb ft).End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00548374
Typical example
Illustration 2 g00606467
Remove valve assembly (1) from piston cooling jet (2) .
Remove piston cooling jet (2) from the cylinder block.Note: The engine crankshaft may be rotated in order to access the piston cooling jet.Note: Ensure that the ball moves freely within the valve assembly of the piston cooling jet. Check that the tube of the piston cooling jet is not damaged.
Inspect the condition of hollow dowel (3). If the hollow dowel is damaged, use a new part for replacement.Note: Hollow dowel (3) is used to locate the piston cooling jet.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00548374
Typical example
Illustration 4 g00606467
Install piston cooling jet (2) in the cylinder block.Note: Ensure that piston cooling jet (2) is properly located on hollow dowel (3). Refer to the Specifications Manual, "Piston Cooling Jet" topic for the correct procedure for the alignment of the piston cooling jet.
Install valve assembly (1) into piston cooling jet (2). Tighten the banjo bolt of valve assembly (1) to a torque of 27 N m (20 lb ft).End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Cat SIS web machinery list:
Parts hose Caterpillar catalog:
5P0767
HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
5P1506
HOSE
3114, 3116, 3176, 3176B, 330 L, 3304, 3306, 3406, 3408, 3412, 3412C, 350, 375, 414E, 416B, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 4...
3114, 3116, 3176, 3176B, 330 L, 3304, 3306, 3406, 3408, 3412, 3412C, 350, 375, 414E, 416B, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 4...
1361953
HOSE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
1945171
HOSE
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3,...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3,...
9X2133
HOSE
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 3...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 3...
7Y1976
HOSE-WATER
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
5P1293
HOSE
120G, 120H, 120H ES, 120H NA, 12G, 130G, 135H, 135H NA, 14H, 16H, 16M, 2384C, 2484C, 322 FM L, 325 L, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 5130, 5130B, 521B, 522B, 559C, 579C, 61...
120G, 120H, 120H ES, 120H NA, 12G, 130G, 135H, 135H NA, 14H, 16H, 16M, 2384C, 2484C, 322 FM L, 325 L, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 5130, 5130B, 521B, 522B, 559C, 579C, 61...
9X2372
HOSE
1090, 1190, 1190T, 1290T, 1390, 3412, 3508, 3512, 3516, 657B, 769D, 771D, 824C, 824G II, 825G II, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 988G, C-9, C7, C9
1090, 1190, 1190T, 1290T, 1390, 3412, 3508, 3512, 3516, 657B, 769D, 771D, 824C, 824G II, 825G II, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 988G, C-9, C7, C9
3650238
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3650202
HOSE-MOLDED
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3834335
HOSE AS
966M, 972M
966M, 972M
4183753
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
4239944
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3670113
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
4183743
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
4183739
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3834293
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3834292
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3834282
HOSE AS
966H, 966M, 966M XE, 972H, 972M, 972M XE
966H, 966M, 966M XE, 972H, 972M, 972M XE
3600286
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3600285
HOSE AS
966H, 966M, 966M XE, 972H, 972M, 972M XE
966H, 966M, 966M XE, 972H, 972M, 972M XE
4501055
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
4239948
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3670398
HOSE AS
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE