AVSPARE.COM
parts catalog

HOSE AS 3905000 - Caterpillar



3905000 HOSE AS Caterpillar parts R1600H HOSE
Rating:
82
Alternative (cross code) number:
CA3905000
390-5000
3905000
Caterpillar 3905000 HOSE AS

Buy HOSE AS 3905000 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP,

Compatible equipment models: 3905000:

LOAD HAUL DUMP  R1600H   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     352-5891     Lifting Strap     2    
B     -     Loctite 771     -    Start By:
Remove hood.
Turn quick disconnect to OFF position.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g02198653
Note: Keep the soot antenna and harness assembly connections clean from contaminants. To prevent contaminants from entering the connections, always plug or cap the connections as they are disconnected.
Disconnect cable assembly (2) and remove soot antenna (1) .
Illustration 2 g02199118
Loosen clamp assembly (4) and slide the clamp assembly away from catalyst (7) .
Disconnect temperature sensor (5) and pressure sensor (6) .
Position Tooling (A) around catalyst (7) . Disconnect clamp assemblies (8) and (3) , and remove the catalyst. The weight of the catalyst (7) is approximately 21 kg (46 lb).
Discard clamp assembly (4) .Installation Procedure
Install the catalyst (7) in reverse order.
Install new clamp assembly (4) . Apply Tooling (B) to the threads of clamp assembly (4) . Tighten clamp assembly (4) to a torque of 50 1 N m (37 1 lb ft). Do not use power tools in order to tighten clamp assembly (4) .
Illustration 3 g02199213
View from below clamp assembly (8) .
Illustration 4 g02199293
Cutaway view of clamp assembly (8) in position on the assembly.
Verify that the cup of the ball joint (G) does not touch the radius of the ball (F) . Position ball clamp (8) and hand tighten ball clamp (8) . Ball Clamp (8) should be in the center of the joint. Dimension (C) and Dimension (D) should be equal within 2 mm (0.08 inch). Repeat the measurements every 90° around ball clamp (8) . If necessary, adjust ball clamp (8) . Do not use power tools in order to torque clamp assembly (8) . Torque ball clamp (8) to a torque of 35 2 N m (26 1 lb ft).
Illustration 5 g02199513
Apply Tooling (B) to the threads of clamp assembly (3) for a Distance (X) . Distance (X) is 25 mm (1 inch) above the trunnion. Use hand tools in order to tighten clamp assembly (3) . Tighten clamp assembly (3) to a torque of 16.5 1.5 N m (146 13 lb in).Note: Keep the soot antenna and cable assembly connections clean from contaminants.
Apply Tooling (B) to the threads of temperature sensor (5) and soot sensor (1) . Tighten temperature sensor (5) and soot sensor (1) to a torque of 45 5 N m (33 4 lb ft). Hand tighten the cable assembly (2) when connecting to soot antenna (1) .

Caterpillar parts catalog:

Caterpillar parts catalog
R1600H Load Haul Dump 9SD00001-UP (MACHINE) POWERED BY C11 Engine


Parts hose Caterpillar catalog:

3R1317 HOSE
24H, 3126B, 3176B, 3176C, 3196, 3304, 3304B, 3306, 3306B, 3456, 572R, 631D, 631G, 637G, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 936, 936F, 95E, 994, C-10, C-12, C-9, CS-643, D6R, D7R, G3306, G936, PM-565, ...
5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
1316645 HOSE
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16M, 215B, 235B, 235D, 3176C, 3196, 330, 330 L...
5P1420 HOSE
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
5P0765 HOSE
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K...
2259644 HOSE AS
R1600, R1600G, R1600H
2259645 HOSE AS
R1600, R1600G, R1600H
2259646 HOSE AS
R1600, R1600G, R1600H
2259647 HOSE AS
R1600, R1600G, R1600H
2261379 HOSE AS
R1600, R1600G, R1600H
2270221 HOSE AS
R1600, R1600G, R1600H
2270220 HOSE AS
R1600, R1600G, R1600H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.