4227715 HOSE-TURBOCHARGER Caterpillar parts
323D2 L, 535D, 545D, 924K, 930K, 938K, C7.1
Rating:
Alternative (cross code) number:
CA4227715
422-7715
4227715
CA4227715
422-7715
4227715
Weight: 0.04 pounds 0 kg.
EXCAVATOR, WHEEL SKIDDER,
Compatible equipment models: 4227715:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     9U-6862     Tapered Brush     1    
C     9U-6863     Small Bore Brush     1    
D     9U-7237     Brush Extension     1    
E     4C-5552     Large Bore Brush     1    
F     8T-2998     Lubricant     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01054374
Use Tooling (B) and Tooling (D) in order to clean electronic unit injector seat (8) .
Use Tooling (C) and Tooling (D) in order to clean electronic unit injector bore (9) .
Use Tooling (E) and Tooling (D) in order to clean the unit injector sleeve.
Illustration 2 g01039929
Do not reuse O-ring seals. New O-ring seals must be used.
Install O-ring seals (7) . Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (F) .
Illustration 3 g01019373
When a fuel injector group is serviced, the new fuel injector group's electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new fuel injector group's electronic code is not entered, the previous fuel injector group's characteristics are assumed.If it is not possible to immediately reprogram the electronic injector code of the injector into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.
Note: Injector code (10) will be located on either the side, as illustrated, or on the top of the injector. Should the code be located in both places, use the code that is located on the side.
If the injectors have been replaced, record injector code (10) for programming.
Illustration 4 g01026993
Install electronic unit injector (2) into the original location in the cylinder head.
Install clamp (6) and spacer (5) .
Do not reuse the injector hold down bolts. New injector hold down bolts must be used.
If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer.
Note: Use new bolt (4) .
Install bolt (4) . Tighten bolt (4) according to the following procedure.
Tighten the bolt for the electronic unit injector to 50 10 N m (37 7 lb ft).
Loosen the bolt until you can turn the bolt by hand.
Tighten the bolt for the electronic unit injector again to 50 10 N m (37 7 lb ft).
Install bridge assemblies (3) in the respective locations.
Connect harness assembly (1) on electronic unit injector (2) . Install the nuts. Tighten the nuts to a torque of 2.5 0.25 N m (22 2 lb in).
Install the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Adjust the height of the electronic unit injector. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust" for
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     9U-6862     Tapered Brush     1    
C     9U-6863     Small Bore Brush     1    
D     9U-7237     Brush Extension     1    
E     4C-5552     Large Bore Brush     1    
F     8T-2998     Lubricant     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01054374
Use Tooling (B) and Tooling (D) in order to clean electronic unit injector seat (8) .
Use Tooling (C) and Tooling (D) in order to clean electronic unit injector bore (9) .
Use Tooling (E) and Tooling (D) in order to clean the unit injector sleeve.
Illustration 2 g01039929
Do not reuse O-ring seals. New O-ring seals must be used.
Install O-ring seals (7) . Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (F) .
Illustration 3 g01019373
When a fuel injector group is serviced, the new fuel injector group's electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new fuel injector group's electronic code is not entered, the previous fuel injector group's characteristics are assumed.If it is not possible to immediately reprogram the electronic injector code of the injector into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.
Note: Injector code (10) will be located on either the side, as illustrated, or on the top of the injector. Should the code be located in both places, use the code that is located on the side.
If the injectors have been replaced, record injector code (10) for programming.
Illustration 4 g01026993
Install electronic unit injector (2) into the original location in the cylinder head.
Install clamp (6) and spacer (5) .
Do not reuse the injector hold down bolts. New injector hold down bolts must be used.
If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer.
Note: Use new bolt (4) .
Install bolt (4) . Tighten bolt (4) according to the following procedure.
Tighten the bolt for the electronic unit injector to 50 10 N m (37 7 lb ft).
Loosen the bolt until you can turn the bolt by hand.
Tighten the bolt for the electronic unit injector again to 50 10 N m (37 7 lb ft).
Install bridge assemblies (3) in the respective locations.
Connect harness assembly (1) on electronic unit injector (2) . Install the nuts. Tighten the nuts to a torque of 2.5 0.25 N m (22 2 lb in).
Install the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Adjust the height of the electronic unit injector. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust" for
Cat SIS web machinery list:
Parts hose Caterpillar catalog:
5P0767
HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
8C3681
HOSE
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16H NA, 225D, 231D, 236D, 242D, 2...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16H NA, 225D, 231D, 236D, 242D, 2...
5P0743
HOSE
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
9X2133
HOSE
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 3...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 3...
1032529
HOSE
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
7Y1976
HOSE-WATER
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
4I3994
HOSE AS
307C, 311C, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320 L, 320B, 320C, 320D, 320D FM, 320D GC, 320D L, 32...
307C, 311C, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320 L, 320B, 320C, 320D, 320D FM, 320D GC, 320D L, 32...
0874531
HOSE AS
307C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 32...
307C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 32...
0875764
HOSE AS
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
4I3988
HOSE AS
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
0875303
HOSE AS
308C, 312C L, 312D, 312D L, 315C, 315D L, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 322...
308C, 312C L, 312D, 312D L, 315C, 315D L, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 322...
1877070
HOSE AS
319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 321D LCR, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324E, 325C FM, 330C FM
319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 321D LCR, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324E, 325C FM, 330C FM
4332039
HOSE
924K, 930K, 938K, C7.1
924K, 930K, 938K, C7.1
4240566
HOSE
924K, 930K, 938K, C7.1
924K, 930K, 938K, C7.1
3924097
HOSE
535D, 545D, 950 GC, C7.1
535D, 545D, 950 GC, C7.1
4222219
HOSE AS
C7.1
C7.1
4222216
HOSE AS
C7.1
C7.1
4236206
HOSE
C7.1
C7.1
6L4726
HOSE
G3306
G3306
2S8810
HOSE ASSEM.
3304, 3306, 768B, 769
3304, 3306, 768B, 769
3S5874
HOSE
951B, 955K, D348
951B, 955K, D348
5S1214
HOSE ASSEM. (18"LONG)
3306, 769
3306, 769
6L9890
HOSE
D399
D399
4S5679
HOSE
225, D399, G353D
225, D399, G353D