HOSE BK 4568466 - Caterpillar

D6D (SA) 38C does not have oil pump (5).(1) Torque for bolts that hold universal joint to drive flange ... 54 7 N m (40 5 lb ft)(2) 2H4406 Springs (four):Length under test force ... 26.2 mm (1.03 in)Test force ... 142 to 167 N (32.0 to 37.5 lb)Free length after test ... 38.9 mm (1.53 in)Outside diameter ... 17.35 mm (.683 in)(3) Thickness of three new discs and two new plates ... 33.38 to 34.68 mm (1.314 to 1.365 in)Thickness of one new 3P3241 Plate ... 6.22 to 6.48 mm (.245 to .255 in)Thickness on one new 4S9072 Disc ... 6.98 to 7.24 mm (.275 to .285 in)(4) 5B3097 Springs (four):Length under test force ... 36.6 mm (1.44 in)Test force ... 196 to 227 N (44 to 51 lb)Free length after test ... 43.0 mm (1.69 in)Outside diameter ... 9.53 mm (.375 in)Adjustment (Flywheel Clutch)
1. Remove clutch inspection cover.2. Turn the flywheel until one of nuts (2) is seen through the opening.3. Loosen the nut approximately two turns and make sure retainer plate (3) is free on the stud.4. Turn flywheel 180° and loosen the other nut and retainer plate.5. Fasten a spring scale to the bottom of the handle for the clutch control lever.6. Turn adjustment ring (1) clockwise (for an increase) or counterclockwise (for a decrease) until the amount of force needed on the spring scale to engage the clutch is ... 200 20 N (45 5 lb)7. Tighten nuts (2) and replace clutch inspection cover. Make sure both nuts (2) are tightened.Adjustment (Flywheel Clutch Brake)
(1) Torque for the nut ... 24 7 N m (18 5 lb ft)1. Move the control lever for the flywheel clutch to the ENGAGED position. Loosen locknut (3). Turn rod (2) until the brake lining just comes in contact with the brake drum.2. Move the control lever for the flywheel clutch to the NOT ENGAGED position. Turn rod (2) two revolutions in the clockwise direction. Tighten locknut (3) to keep the rod in position.Adjustment (Flywheel Clutch Control Linkage)
(A) Dimension ... 125.0 3.0 mm (4.92 .12 in)(4) Torque for locknuts ... 100 15 N m (75 11 lb ft)(5) Torque for locknuts ... 100 15 N m (75 11 lb ft)1. Put control lever (1) in the ENGAGED position.2. Make an adjustment to the length of rod (3) until dimension (A) between the centerline of control lever (1) and the outer edge of cover (2) is ... 125.0 3.0 mm (4.92 .12 in)Adjustment (Flywheel Clutch Interlock Linkage)
D6D (SR) Linkage Shown(A) Dimension between the centers of pins (1) and (2)38C ... 385.8 mm (15.19 in)7XF ... 386.6 mm (15.22 in)8FJ ... 386.6 mm (15.22 in)(4) Torque for locknut ... 12 4 N m (9 3 lb ft)1. Adjust length of rod (5) to dimension (A).2. With the adjustment of the interlock linkage correct, the lever which connects with rod end (3) will be at