4906788 HOSE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA4906788
490-6788
4906788
CA4906788
490-6788
4906788
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
GOWE 50MT Starter Motor 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
GOWE 50MT Starter Motor 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
$1,311.00
03 Jul 2022
US: Gowegroup
GOWE 50MT Starter Motor 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
GOWE 50MT STARTER MOTOR 1109222 1109285 1109286 3021038,4906788,3636821,10479124,133261,186396,3021038 FOR CUMMINS KTA19
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to the piston cooling jet.
Illustration 1 g01340939
Remove bolt (1) and piston cooling jet (2) from the cylinder block.
Repeat steps 1 and 2 for the remaining piston cooling jets. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Name Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01340940
Clean the piston cooling jets and inspect the piston cooling jets for damage. Ensure that the valve is free to move within each piston cooling jet. Replace any damaged piston cooling jets. The procedure for checking the alignment of the piston cooling jets is described in Specifications, "Piston Cooling Jet Alignment".
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to access the mounting flange for the piston cooling jet.
Position piston cooling jet (2) in the cylinder block. Install bolt (1). Tighten bolt (1) to a torque of 9 N m (80 lb in).
Repeat steps 2 through 3 for the remaining piston cooling jets. End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Required Tools
Tool Part Number Part Name Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to the piston cooling jet.
Illustration 1 g01340939
Remove bolt (1) and piston cooling jet (2) from the cylinder block.
Repeat steps 1 and 2 for the remaining piston cooling jets. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Name Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01340940
Clean the piston cooling jets and inspect the piston cooling jets for damage. Ensure that the valve is free to move within each piston cooling jet. Replace any damaged piston cooling jets. The procedure for checking the alignment of the piston cooling jets is described in Specifications, "Piston Cooling Jet Alignment".
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to access the mounting flange for the piston cooling jet.
Position piston cooling jet (2) in the cylinder block. Install bolt (1). Tighten bolt (1) to a torque of 9 N m (80 lb in).
Repeat steps 2 through 3 for the remaining piston cooling jets. End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Parts hose Caterpillar catalog:
4906774
HOSE AS
Caterpillar
Caterpillar
4906773
HOSE AS
Caterpillar
Caterpillar
4906772
HOSE AS
Caterpillar
Caterpillar
4906675
HOSE AS
Caterpillar
Caterpillar
4903870
HOSE AS
Caterpillar
Caterpillar
4903530
HOSE AS
Caterpillar
Caterpillar
4906824
HOSE AS
Caterpillar
Caterpillar
4906819
HOSE AS
Caterpillar
Caterpillar
4906812
HOSE AS
Caterpillar
Caterpillar
4906809
HOSE AS
Caterpillar
Caterpillar
4906808
HOSE AS
Caterpillar
Caterpillar
4906797
HOSE AS
Caterpillar
Caterpillar