HOSE 4920464 - Caterpillar

4920464 HOSE Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4920464
492-0464
4920464

Weight: 2 pounds 1 kg.

Buy HOSE 4920464 Caterpillar genuine, new aftermarket tractor parts with delivery

You can buy:

Water Pump 4920464 4089909 for Cummins Engine ISX15 QSX15

US$450.16

28 May 2025

FridayParts

Water Pump 4920464 4089909 for Cummins Engine ISX15 QSX15

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Water Pump 4920464 For Cummins QSX15 Diesel Engine Parts

$344.94

15 Oct 2025

CN: Star Mustang En

Water Pump 4920464 For Cummins QSX15 Diesel Engine Parts
STAR MUSTANG

$450.00

15 Oct 2025

US: cqinglilingwenh

Water Pump 4920464 4089909 for Cummins Engine ISX15 QSX15
weiwie Part Number:4920464 || Application:For Cummins Engine ISX15 QSX15

IMIFAFTAbT 4920464 4089909 Water Pump Fits for Cummins Engine ISX12 ISX15 QSX15

$369.00

05 Aug 2025

CN: ziwangcjx

IMIFAFTAbT 4920464 4089909 Water Pump Fits for Cummins Engine ISX12 ISX15 QSX15
IMIFAFTAbT Product Name: 4920464 4089909 Water Pump || Part number: 4920464 4089909 || Fits for Cummins Engine ISX12 ISX15 QSX15 || 1 PCS Water Pump || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate

Number on catalog scheme: 5

For full view, you need register

Information:

Test Procedure
System Operation
An energized input closes the N.O. contacts. An energized input opens the N.C. contacts. Digital modules are used to determine whether a circuit is ON/OFF. A number of modules are available. The most common modules have sixteen channels.
Illustration 1 g00563503
Diagram of the programmable logic controller
Illustration 2 g00563591
Schematic of the discrete inputFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Verify the value of the channel.
Get on-line with the PLC.
Locate the software address for the channel.The results of the preceding procedure are in the following list:
The channel has a software address. Proceed to 3.
The channel does not have a software address. Replace the module. Verify that the repair resolves the problem. Refer to Maintenance Procedure, "Input Module and Output Module - Replace". Stop.
Apply the rated voltage.
Apply the rated voltage to the channel.
Verify that the address changed from zero to one.Note: The LED will illuminate when the rated voltage is applied to the channel.The results of the preceding procedure are in the following list:
The software address value changes. The module is functioning normally. Stop.
The software address value does not change. the module is not functioning normally. Replace the module. Verify that the repair resolves the problem. Refer to Maintenance Procedure, "Input Module and Output Module - Replace". Stop.