4994939 HOSE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA4994939
499-4939
4994939
CA4994939
499-4939
4994939
You can buy:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Haiyazhma Fuel Drain Tube 4994939 5341887 Compatible with Cummins Engine ISDE ISB6.7
Haiyazhma Part Name: Fuel Drain Tube || Part Number: 4994939 5341887 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: ISB6.7 || Applicable: Compatible with Cummins Engine ISDE ISB6.7 || Package included: 1pcs Fuel Drain Tube 4994939 5341887
Haiyazhma Part Name: Fuel Drain Tube || Part Number: 4994939 5341887 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: ISB6.7 || Applicable: Compatible with Cummins Engine ISDE ISB6.7 || Package included: 1pcs Fuel Drain Tube 4994939 5341887
Information:
and ground.
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.
Remove all wire jumpers and reconnect all connectors.Expected Result:The voltage at the ECM is 24 3 VDC for two seconds.Results:
OK - The voltage at the ECM is 24 3 VDC for two seconds.Repair: The wire F710-BR and/or the connectors between the ECM and the ether start relay need repair. Inspect the wiring and connectors between the ether start relay and the connector at the ECM. Repair the connectors or wiring and/or replace the connectors or wiring.STOP
Not OK - The voltage at the ECM is not 24 3 VDC for two seconds.Repair: Replace the ECM. Refer to the diagnostic procedure Troubleshooting, "Replacing the ECM".STOPTest Step 9. Check the Voltage from the Ether Hold Relay.
Turn the ECS to the OFF/RESET position.
Connect a voltmeter between wire 926-RD on terminal 30 of the ether hold relay and ground.
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.Expected Result:The voltage at terminal 30 is 24 3 VDC during injection.Results:
OK - The voltage at terminal 30 is 24 3 VDC during injection. Proceed to Test Step 10.
Not OK - The voltage at terminal 30 is not 24 3 VDC during injection. Proceed to Test Step 12.Test Step 10. Check the Voltage at the Resistor and the Diode Assembly.
Turn the ECS to the OFF/RESET position.
Disconnect the connector at the resistor and the diode assembly.
Connect a voltmeter to pin 1 of the resistor and the diode assembly and ground.
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. This procedure must be performed on all of the resistor and diode assemblies, if more than one resistor and diode assembly is present. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.Expected Result:The voltage is 24 3 VDC.Results:
OK - The voltage is 24 3 VDC. Proceed to Test Step 11.
Not OK - The voltage is not 24 3 VDC.Repair: There is a problem in the harness between the ether hold relay and the resistor and diode assembly. Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 11. Check the Resistor and Diode Assembly.
Disconnect the connector at the resistor and the diode assembly.
Set the multimeter to the "Check Diode" setting.
Connect the positive lead of the multimeter
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.
Remove all wire jumpers and reconnect all connectors.Expected Result:The voltage at the ECM is 24 3 VDC for two seconds.Results:
OK - The voltage at the ECM is 24 3 VDC for two seconds.Repair: The wire F710-BR and/or the connectors between the ECM and the ether start relay need repair. Inspect the wiring and connectors between the ether start relay and the connector at the ECM. Repair the connectors or wiring and/or replace the connectors or wiring.STOP
Not OK - The voltage at the ECM is not 24 3 VDC for two seconds.Repair: Replace the ECM. Refer to the diagnostic procedure Troubleshooting, "Replacing the ECM".STOPTest Step 9. Check the Voltage from the Ether Hold Relay.
Turn the ECS to the OFF/RESET position.
Connect a voltmeter between wire 926-RD on terminal 30 of the ether hold relay and ground.
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.Expected Result:The voltage at terminal 30 is 24 3 VDC during injection.Results:
OK - The voltage at terminal 30 is 24 3 VDC during injection. Proceed to Test Step 10.
Not OK - The voltage at terminal 30 is not 24 3 VDC during injection. Proceed to Test Step 12.Test Step 10. Check the Voltage at the Resistor and the Diode Assembly.
Turn the ECS to the OFF/RESET position.
Disconnect the connector at the resistor and the diode assembly.
Connect a voltmeter to pin 1 of the resistor and the diode assembly and ground.
Turn the ECS to the STOP position.
Activate the ether override and observe the voltmeter while ether injection is on. Disable the ether override. This procedure must be performed on all of the resistor and diode assemblies, if more than one resistor and diode assembly is present. Do not allow the ether to be on for more than two minutes. Damage to the solenoid may occur.Expected Result:The voltage is 24 3 VDC.Results:
OK - The voltage is 24 3 VDC. Proceed to Test Step 11.
Not OK - The voltage is not 24 3 VDC.Repair: There is a problem in the harness between the ether hold relay and the resistor and diode assembly. Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 11. Check the Resistor and Diode Assembly.
Disconnect the connector at the resistor and the diode assembly.
Set the multimeter to the "Check Diode" setting.
Connect the positive lead of the multimeter
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
4993959
HOSE
Caterpillar
Caterpillar
4991528
HOSE AS
Caterpillar
Caterpillar
4984607
HOSE AS
Caterpillar
Caterpillar
4983121
HOSE
Caterpillar
Caterpillar
4983001
HOSE AS
Caterpillar
Caterpillar
4982827
HOSE AS
Caterpillar
Caterpillar
5024194
HOSE-AFTERCOOLER
Caterpillar
Caterpillar
5024193
HOSE-AFTERCOOLER
Caterpillar
Caterpillar
5024190
HOSE-AFTERCOOLER
Caterpillar
Caterpillar
5024189
HOSE-AFTERCOOLER
Caterpillar
Caterpillar
5023514
HOSE
Caterpillar
Caterpillar
5000390
HOSE
Caterpillar
Caterpillar