AVSPARE.COM
parts catalog

HOSE A 4Z4549 - Caterpillar



4Z4549 HOSE A Caterpillar parts HOSE
Rating:
41
Alternative (cross code) number:
CA4Z4549
4Z-4549
4Z4549
Caterpillar 4Z4549 HOSE A
Weight: 4 pounds 1 kg.

Buy HOSE A 4Z4549 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 1
Diagnostic Trouble Codes for Ether Injection
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
626-5 2417-5 Ether Injection Control Solenoid : Current Below Normal The Electronic Control Module (ECM) detects a low current condition in the output from the ECM to the solenoid for ether injection.
The code is latched. The code is logged.
Ether injection is disabled.
626-6 2417-6 Ether Injection Control Solenoid : Current Above Normal The ECM detects a high current condition in the output from the ECM to the solenoid for ether injection.
The code is latched. The code is logged.
Ether injection is disabled. The ether injection system will improve cold weather starting of the engine. The engine Electronic Control Module (ECM) controls the ether injection system. The ether injection system is disabled if there is an active engine shutdown.Activation of the ether starting aid is based from a map using the coolant temperature, intake manifold temperature, and atmospheric pressure. Refer to Illustration 1.
Illustration 1 g02445796The following conditions must be met for the ether injection system to be enabled:
Ether injection is set to "Enabled" in the electronic service tool
Engine coolant temperature is less than the "Start Aid Selection Temperature - Coolant". Refer to Illustration 1.
Intake manifold temperature is less than the "Start Aid Selection Temperature - IMAT."
Coolant temperature and intake manifold air temperature are within 11° C of each other.
Illustration 2 g01696575
Ether starting aid group (typical example)
(1) Ether injection solenoid
Illustration 3 g01155187
Terminal locations at the harness connector for the ether solenoid
(1) Ether enable solenoid
(2) Return for ether injection solenoid
Illustration 4 g03712340
Schematic for the ether injection system
Not all connectors are shown. Refer to the appropriate electrical schematic.
Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Remove the electrical power from the ECM.
B. Thoroughly inspect the ECM connector J1/P1. Inspect all the other connectors for the circuit. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
D. Check the ECM connector (allen head screw) for the correct torque of 6 N m (53 lb in).
E. Check the harness and the wiring for abrasion and for pinch points.
Loose connection or damaged wire
Result: The harness and wiring are OK.
Proceed to Test Step 2.
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Proceed to Test Step 4.
2. Check the Wiring Between the ECM and the Ether Injection Solenoid
The ether canister must be removed prior to performing this procedure.
A. Verify that the keyswitch is in the OFF position.
B. Remove the ether canister.
C. Disconnect the engine harness connector for the ether injection solenoid.
D. Connect a digital voltmeter across the two terminals on the engine harness connector for the ether injection solenoid.
E. Turn the keyswitch to the ON position.
F. Measure the voltage across the terminals


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.