HOSE AS 5259491 - Caterpillar

Table 1
J1939 Code and Description CDL Code and Description Comments
3711-31
DPF Active Regeneration Inhibited Due to Low Exhaust Gas Temperature E593 (2)
Aftertreatment Insufficient Temperature to Complete Regeneration Active regeneration failed due to an inability of the Diesel Particulate Filter (DPF) to reach a high enough temperature. The code is logged. Engine power is derated.
Table 2
Associated Diagnostic Trouble Codes
102-18
3480-15
3480-16
3480-17
3480-18
4077-15
4077-16
4077-17
4077-18
E1050
E1051
E1052
E1053 Note: The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, the Manual DPF Regeneration must be performed using Cat ET.
Table 3
Troubleshooting Test Steps Values Results
1. Check for Associated Codes
A. Establish communication between Cat ET and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing associated diagnostic trouble codes.
C. Table 2 lists the diagnostic trouble codes that are associated with the E593 (2) or 3711-31 code. Determine if any of the codes in Table 2 are present.
Associated Codes
Result: An associated code is not present.
Proceed to Test Step 2.
Result: An associated code is present.
Repair: Troubleshoot the associated code.
2. Check the Current Flow Through the Heater
A. Verify that the engine is off. Check the current flow through the heater. Refer to Systems Operation/Testing and Adjusting, "ARD Nozzle Heater (Current) - Test" for the correct procedure.
Note: Between 7.0 A and 14 A for a 12 V system. Or, between 3.5 A and 7 A for a 24 V system
Current
Result: The current flow is OK.
Proceed to Test Step 3.
Result: The current flow is not between 7.0 A and 14 A for a 12 V system. Or, the current flow is not between 3.5 A and 7 A for a 24 V system.
Repair: There may be a problem with the ARD nozzle. Refer to Troubleshooting, "ARD Nozzle Heater - Test".
3. Inspect the Tubing Between the Compressor and the Combustion Air Valve
A. Check for cracks in the tubing.
B. Check for loose or damaged hardware.
Tubing
Result: The tubing is not damaged or cracked.
Proceed to Test Step 4.
Result: The tubing is damaged or cracked.
Repair: Replace or repair the tubing.
Proceed to Test Step 5.
4. Inspect the tubing from the Combustion Air Valve to the Combustion Air Absolute Pressure Sensor.
A. Check for cracks in the tubing.
B. Check for any air leaks.
C. Check the clamps on the tube and ensure that the clamps are tightened.
Tubing
Result: The tubing is damaged or cracked.
Repair: Replace or repair the tubing.
Proceed to Test Step 5.
Result: The tubing is not damaged or cracked.
Repair: Replace the combustion air valve. Refer to Disassembly and Assembly, Air Control Valve - Remove and Install.
Proceed to Test Step 5.
5. Perform the "ARD Air System Service Test"
A. Reset all active codes and clear all logged codes. Use Cat ET to perform an "ARD Air System Service Test" to verify that the problem is resolved.
ARD Air System Service Test
Result: The "ARD Air System Service Test" passed.
Proceed to Test Step 6.
Result: The "ARD Air System Service Test" failed.
Repair: There is a problem with the ARD combustion