HOSE 5340556 - Caterpillar

Illustration 3 g03202740
Left side close-up view of manual valve assembly (1) 126-8790 Manual Valve As (2) 376-7218 Plate (4) 385-1045 Hydraulic Block (5) 385-1046 Spacer (7) 1P-3703 Rectangular Seal (9) 3D-2824 O-Ring Seal (11) 5P-8245 Hard Washer (12) 5P-9436 Plug (14) 6A-5591 Bolt (15) 6V-5839 Washer (16) 6V-7744 Locknut (17) 6V-8336 Bolt (18) 6V-8716 Connector (19) 6V-9746 O-Ring Seal (20) 7M-8485 O-Ring Seal (21) 7X-2549 Bolt (23) 8T-0644 Bolt (24) 8T-4223 Hard Washer (26) 8T-6451 Elbow
Illustration 4 g03202773
Right side view of stick (A) Existing hose (1) 126-8790 Manual Valve As (3) 384-7931 Hydraulic Block (6) 421-8416 Hose As
Illustration 5 g03202799
Right side close-up view of manual valve assembly (1) 126-8790 Manual Valve As (2) 376-7218 Plate (3) 385-1044 Hydraulic Block (5) 385-1046 Spacer (8) 1P-3704 Rectangular Seal (9) 3D-2824 O-Ring Seal (11) 5P-8245 Hard Washer (12) 5P-9436 Plug (14) 6A-5591 Bolt (15) 6V-5839 Washer (16) 6V-7744 Locknut (17) 6V-8336 Bolt (18) 6V-8716 Connector (19) 6V-9746 O-Ring Seal (20) 7M-8485 O-Ring Seal (21) 7X-2549 Bolt (23) 8T-0644 Bolt (24) 8T-4223 Hard Washer (26) 8T-6451 Elbow
Install manual valve assembly (1) onto plate (2) using the following parts: two bolts (23), four washers (15) and two locknuts (16). Tighten to standard torque.
Install O-ring seals (20) and connectors (18) on to manual valve assembly (1) .
Install plug (12) with O-ring seal (9) into the back of hydraulic block (4) on the left side lines.Note: Use hydraulic block (3) on the right side lines.Note: Do not tighten the following connections until all components are installed and arranged properly.
Install O-ring seal (9) onto elbow (26) and connect to hydraulic block (4) on the left side lines.Note: Use hydraulic block (3) on the right side lines.
Disconnect existing hose (A) and install hydraulic block (4) using the following parts: two rectangular seals (7), four bolts (21) and four washers (24) on the left side lines. Arrange as shown in Illustration 3.Note: Use hydraulic block (3) and rectangular seals (8) on the left side lines. Refer to Illustration 5.
Install O-ring seals (19) into connectors (18) on manual valve assembly (1) and connect to elbow (26) .
Mount manual valve assembly (1) to the stick by installing plate (2) using bolts (14) and washers (11). Arrange as shown in Illustrations 3 and 5.Note: Use spacer (5) when the four bolt flange on the hydraulic lines is arranged vertically. The hydraulic block must be rotated horizontally for this arrangement. Otherwise this part is not needed. Use bolts (17) when spacer (5) is used. If the spacer is not needed use bolts (14) .
Connect