5366137 HOSE & TUBE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA5366137
536-6137
5366137
CA5366137
536-6137
5366137
Weight: 2 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$89.47
13 Aug 2021
US: SEKEGE
Spiral Point Tap,9/16"-18,HSS-E
WIDIA-GTD The TiCN coating on these taps protects them from wear and is harder and more wear-resistant than a
WIDIA-GTD The TiCN coating on these taps protects them from wear and is harder and more wear-resistant than a
$10.87
13 Aug 2021
Amazon.com
WIDIA GTD VTSPO5094 VariTap VTSPO50 Multipurpose Tap, Plug Chamfer, Right Hand Cut, 3 Flutes, 9/16-18, HSS-E, TiCN Coating
WIDIA Unique spiral-point geometry provides low tapping torque while pushing chips ahead of the tap in through holes || Manufactured from high-vanadium hss-e to provide long and consistent tool life || Ideal for customers who have a variety of materials to machine || Form b plug chamfer, ansi || Machine screw and fractional
WIDIA Unique spiral-point geometry provides low tapping torque while pushing chips ahead of the tap in through holes || Manufactured from high-vanadium hss-e to provide long and consistent tool life || Ideal for customers who have a variety of materials to machine || Form b plug chamfer, ansi || Machine screw and fractional
Number on catalog scheme:
17
For full view, you need register
Information:
Heading
The heading is the direction that the machine is traveling, shown in degrees, clockwise from grid north. 0 degrees equals North, 180 degrees equals South. The heading is calculated by comparing the left GPS antenna with the right GPS antenna.Guidance for a single antenna system is not given when the machine has just been started or when the machine has lost the GPS signal.The message "Low Accuracy GPS" flashes on the display. In this situation, wait until you are receiving high accuracy GPS signals again.Pitch
Pitch is the forward or aft angle of the machine, calculated in degrees from the horizontal (0 degrees). Pitch is expressed in percentage or "Rise: Run" depending on the unit settings. The pitch is considered positive when the angle is above the horizontal (up at the front). The pitch is considered negative when the angle is below the horizontal (down at the front).The pitch is calculated with the information from the pitch sensor. The AccuGrade system uses the pitch of the machine body in order to determine the bucket pitch.Pitch will become inaccurate if the pitch sensor is not connected. The message "Check Pitch Sensor"flashes on the display. In this situation, make sure that the pitch sensor is connected to the CAN bus.Orientation
Orientation is the direction in which the bucket is facing. The orientation is calculated from the vector between the two antennas.Cross Slope
Cross slope is the cross fall of the bucket, orthogonal to the direction of travel (machine heading). This is significant when the machine has a bucket that can be angled with respect to the body of the machine. Positive cross slope rises to the right. With respect to the left bucket tip, the cross slope is considered positive when the right bucket tip is high, and negative when the right bucket tip is low.
The heading is the direction that the machine is traveling, shown in degrees, clockwise from grid north. 0 degrees equals North, 180 degrees equals South. The heading is calculated by comparing the left GPS antenna with the right GPS antenna.Guidance for a single antenna system is not given when the machine has just been started or when the machine has lost the GPS signal.The message "Low Accuracy GPS" flashes on the display. In this situation, wait until you are receiving high accuracy GPS signals again.Pitch
Pitch is the forward or aft angle of the machine, calculated in degrees from the horizontal (0 degrees). Pitch is expressed in percentage or "Rise: Run" depending on the unit settings. The pitch is considered positive when the angle is above the horizontal (up at the front). The pitch is considered negative when the angle is below the horizontal (down at the front).The pitch is calculated with the information from the pitch sensor. The AccuGrade system uses the pitch of the machine body in order to determine the bucket pitch.Pitch will become inaccurate if the pitch sensor is not connected. The message "Check Pitch Sensor"flashes on the display. In this situation, make sure that the pitch sensor is connected to the CAN bus.Orientation
Orientation is the direction in which the bucket is facing. The orientation is calculated from the vector between the two antennas.Cross Slope
Cross slope is the cross fall of the bucket, orthogonal to the direction of travel (machine heading). This is significant when the machine has a bucket that can be angled with respect to the body of the machine. Positive cross slope rises to the right. With respect to the left bucket tip, the cross slope is considered positive when the right bucket tip is high, and negative when the right bucket tip is low.
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
5366136
HOSE & TUBE AS
Caterpillar
Caterpillar
5364988
HOSE AS
Caterpillar
Caterpillar
5362598
HOSE AS
Caterpillar
Caterpillar
5357100
HOSE AS
Caterpillar
Caterpillar
5327254
HOSE AS
Caterpillar
Caterpillar
5324586
HOSE AS
Caterpillar
Caterpillar
5384777
HOSE AS
Caterpillar
Caterpillar
5384769
HOSE AS
Caterpillar
Caterpillar
5384761
HOSE AS
Caterpillar
Caterpillar
5384758
HOSE AS
Caterpillar
Caterpillar
5382639
HOSE & TUBE AS
Caterpillar
Caterpillar
5382638
HOSE & TUBE AS
Caterpillar
Caterpillar