5366787 HOSE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA5366787
536-6787
5366787
CA5366787
536-6787
5366787
Information:
Install yellow bands (5) on hose (15) .
Install red bands (4) on hose (14) .
Install hose assembly (14) into the lower port of the cylinder for the coupler. Use the necessary tooling in order to tighten the hose into the port. Fully tighten this hose before performing the next step. Refer to Illustration 9.
Install union (44) to the other end of hose (14) .
Illustration 10 g01509374
Install hose assembly (15) into the remaining port on the quick coupler. Refer to Illustration 10.
Install union (45) into the other end of hose assembly (15) .
Secure both hose assemblies. Use clamp (9), plate (2), and bolt (47). Make sure that there is enough clearance for the hoses when the coupler is in a full curl position.
Illustration 11 g01486453
(4) Hose band (5) Hose band (13) Hose assembly (25) Hose assembly (26) Hose assembly (27) Hose assembly (33) Reducer (35) Tee (40) O-ring seal (42) O-ring seal (44) Face seal union (48) Hard washer
Route hose assemblies (13) and (25) to the base of the boom.
Install yellow bands (5) on hose (27) .
Install red bands (4) on hose (26) .
Temporarily connect hose assembly (13) to hose assembly (26). Temporarily connect hose assembly (25) to hose assembly (27). Refer to Illustration 11 for the proper fittings.
Illustration 12 g01486516
(4) Hose band (5) Hose band (14) Hose assembly (15) Hose assembly (26) Hose assembly (27) Hose assembly (28) Permanent coupling assembly (29) Permanent coupling assembly (44) Face seal union (45) Face seal union
Install the cable straps in order to secure hose assemblies (13) and (25) .
Temporarily route hose assemblies (26) and (27) along the stick and the boom. Refer to Illustration 12.
Mark hose assemblies (26) and (27) in order to cut to length.
Remove hose assemblies (26) and (27) from the host machine.
Cut hose assemblies (26) and (27) at the marks.
Attach coupling (28) to the hose with the red marker.
Attach coupling (29) to the hose with the yellow marker.
Permanently install hose assemblies (26) and (27) to the stick and to the boom.
Install the cable straps in order to secure the hose assemblies.Installation Procedure for the Electrical Components
Illustration 13 g01487498
(24) Harness assembly (54) "AL-C2" (55) "AL-C1" (56) Ground strap
Attach wiring harness (24) to valve group (20) .
Route the wire harness across the boom foot toward the RH mainframe then rearward. There is a ground strap (56) that is located halfway down the length of the harness. Attach ground strap (56) to the frame. Refer to Illustration 13.
Illustration 14 g01491593
(55) "AL-C1" Connection (57) "780 PU" Chassis harness
Connect the harness to the existing wiring harness for the chassis that is located low on the RH mainframe.
Illustration 15 g01247692
Location for switch assembly
Remove the panel cover that is located on the right side of the seat.
Illustration 16 g01487614
(18) Bracket assembly
A bracket assembly (18) is supplied for use on the 311D RR.
Illustration 17 g01487635
(19) Cover (21) Bracket assembly for 314D CR (23) Switch (53) Truss head screw (58) "147 PU" connection (59) "E562 PU" connection
Assemble the switch. Refer to Illustration 17.
Illustration 18 g01510013
(17) Wiring harness (60) Factory installed harness (coupler)
Connect the cab wiring to
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
5366786
HOSE AS
Caterpillar
Caterpillar
5366785
HOSE AS
Caterpillar
Caterpillar
5366508
HOSE AS
Caterpillar
Caterpillar
5366507
HOSE AS
Caterpillar
Caterpillar
5335893
HOSE
Caterpillar
Caterpillar
5334723
HOSE-REDUCER
Caterpillar
Caterpillar
5389145
HOSE AS
Caterpillar
Caterpillar
5389142
HOSE AS
Caterpillar
Caterpillar
5375896
HOSE AS
Caterpillar
Caterpillar
5369114
HOSE AS
Caterpillar
Caterpillar
5368872
HOSE & TUBE AS
Caterpillar
Caterpillar
5368870
HOSE AS
Caterpillar
Caterpillar