HOSE AS 5526087 - Caterpillar

5526087 HOSE AS Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA5526087
552-6087
5526087

Buy HOSE AS 5526087 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

High Performance Silicone Heater Hose - 7/8" ID x 40 ft Blue (.875"|22mm)

$289.99

02 Feb 2022
12.8[5.76] Pounds
US: hpcouplers

High Performance Silicone Heater Hose - 7/8" ID x 40 ft Blue (.875"|22mm)
hpcouplers Manufactured in the USA - 100% Satisfaction Guarantee || .160" Wall Thickness - Nearly 3x the thickness of cheap hose. || Extreme Temperature Resistance with Superior Flexibility ( -65F / +350F ) More on Temp rating below. || Meets or Exceeds all SAE J20 R3 Class A + TMC RP303B Class I Grade II Certifications || Actual Burst Pressure 250psi / SAE J20 R1 175psi

FlexFab - 7/8" ID x 25 ft 5526 Blue Silicone Heater Hose 22mm 350F Radiator Coolant .88"

$129.99

07 Jun 2021
7.2[3.24] Pounds
US: hpcouplers

FlexFab - 7/8" ID x 25 ft 5526 Blue Silicone Heater Hose 22mm 350F Radiator Coolant .88"
FlexFab Flexfab 5526-087 25 ft || Inside Diameter (ID): 0.88" (22mm) || Outside Diameter (OD): 1.21" (31mm)

High Performance Silicone Heater Hose - 7/8" ID x 5 ft Blue (.875"|22mm)

$39.99

05 Jul 2021
1.44[0.65] Pounds
US: hpcouplers

High Performance Silicone Heater Hose - 7/8" ID x 5 ft Blue (.875"|22mm)
hpcouplers Manufactured in the USA - 100% Satisfaction Guarantee || .160" Wall Thickness - Nearly 3x the thickness of cheap hose. || Extreme Temperature Resistance with Superior Flexibility ( -65F / +350F ) More on Temp rating below. || Meets or Exceeds all SAE J20 R3 Class A + TMC RP303B Class I Grade II Certifications || Actual Burst Pressure 250psi / SAE J20 R1 175psi

For full view, you need register

Information:

Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 9S-1366 Bolt 2 Start By:
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Illustration 1 g01205960
Remove bolts (5) and gear (4) .
Put an alignment mark across housing (1) and water pump housing (3). The orientation of the housings is different on the left water pump and the right water pump.
Remove bolts (2). Separate housing (1) from water pump housing (3). Remove the O-ring seal from water pump housing (3) .
Illustration 2 g01205982
Loosen bolt (6). Do not remove the bolt. Use a block and Tooling (B) in order to put tension on the impeller. Tap the center of the block in order to loosen impeller (8) on the shaft. Remove bolt (6) and washer (7) .
Illustration 3 g01205985
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove impeller (8) .
Illustration 4 g01206070
Illustration 5 g01206072
Remove spring (10) from shaft (9) .
Remove seal (11) .
Illustration 6 g01206073
Remove bolts (12) and thrust washer (13) .
Illustration 7 g01206085
Remove shaft (9) .
Illustration 8 g01206088
If necessary, use Tooling (A) and a suitable press in order to remove seal (14) .Note: Check the O-ring seals for wear or damage. If necessary, replace the O-ring seals.
Illustration 9 g01206116
Remove bearings (15) and bearings (16) from water pump housing (3) .