9R2638 HOSE AS Caterpillar parts
416, 428
Rating:
Alternative (cross code) number:
CA9R2638
9R-2638
9R2638
CA9R2638
9R-2638
9R2638
Weight: 3 pounds 1 kg.
BACKHOE LOADER,
Number on catalog scheme:
10
For full view, you need register
Information:
Illustration 1 g02572797
Schematic of the Dump Solenoid 1
This diagnostic code is associated with the Dump Solenoid 1. The FMI 05 means that the ECM has detected that the current for the solenoid circuit is below normal.Conditions that cause this diagnostic code to be activated are:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. The failure of the ECM is unlikely. Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected.Test Step 1. CHECK THE SOLENOID
Disconnect the solenoid from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire E922-GN(Green)) to contact 2 (wire H716-WH(White)).
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the CID 0356 FMI 05 diagnostic code. Expected Result:The CID 0356 FMI 05 diagnostic code is no longer active. A CID 0356 FMI 06 diagnostic code becomes active when the jumper wire is connected.Results:
YES - The CID 0356 FMI 05 diagnostic code is no longer active. A CID 0356 FMI 06 diagnostic code becomes active when the jumper wire is connected. The solenoid has failed.Repair: Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The CID 0356 FMI 05 diagnostic code remains active. The jumper wire does not affect the status of the active diagnostic code. The solenoid is not causing the problem. Proceed to Test Step 2.Test Step 2. CHECK THE CIRCUIT FOR AN OPENThe jumper wire that was installed in the previous Test Step remains in place.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness ECM connector J1 from the ECM.
At the machine harness connector J1 for the ECM, measure the resistance from contact J1-52 (wire E922-GN(Green)) to contact J1-50 (wire H716-WH(White)).
While observing the multimeter resistance measurement, wiggle the machine harness connectors for the ECM and wiggle the machine harness connector for the solenoid. Gently pull on the wires and move the wires around. Expected Result:The resistance measurement is less than 5.0 ohms at all times during the manipulation of the harness and connectors.Results:
OK - The resistance measurement is less than 5.0 ohms. The resistance measurement is not indicating an open or a bad connection in the circuit. Proceed to Test Step 3.
NOT OK - The resistance measurement is greater than 5.0 ohms. The resistance
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
3208, 3304, 3304B, 3306, 3306B, 426, 428, 525B, 535B, 545, 561C, 637D, D25C, D30C, D350C, D35C, D5B, G3306, G3306B, RM-300
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
215, 216, 228, 235, 235C, 236, 236B, 247, 248, 252B, 267, 267B, 268B, 287, 301.5, 301.6C, 302.5C, 303, 304, 305, 307B, 3116, 3126, 3176B, 3176C, 3196, 3208, 3306B, 3406E, 3456, 345B, 345B II, 345B II ...
120G, 12G, 130G, 140G, 416B, 416C, 426, 426C, 428
414E, 416B, 416C, 416D, 416E, 420D, 422E, 424D, 426B, 426C, 428, 428B, 428C, 428D, 430D, 436C, 438B, 438C, D8R
416, 416B, 416C, 416D, 416E, 420D, 420E, 426B, 426C, 430D, 430E, 436C
414E, 416B, 416C, 416D, 416E, 420D, 422E, 424D, 426B, 426C, 428, 428B, 428C, 428D, 430D, 436C, 438B, 438C
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 30...
416, 428
416, 426, 428, 436
416, 426, 428, 436, 615C, 776C, 776D, 777D
428, 428B, 438
4W2947
HOSE AS
426, 428
426, 428
215, 215B, 3126, 3126B, 3126E, 3208, 3304, 3306, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 834B, ...
3208, 3304, 3306, 3406, 615, 769C, 769D, 771C, 771D, AD40, AD45, AE40, AE40 II
4H0008
HOSE AS-FLEXIBLE
3306, 3406, 3406B, 3408, G3306, G343
3306, 3406, 3406B, 3408, G3306, G343
3176B, 3176C, 3196, 3306, 3406B, 3408, 3408C, 3412, 3412E, C-12, C12, C30, C32, G3408, G3412
1674, 3304, 3306, 3406, 3408, D334, D353C, D379A, D379B, D398, D399, D6D, G379, G398, G399
9R2145
HOSE AS
416, 428
416, 428
9R2143
HOSE AS
416, 426, 428
416, 426, 428
5P5645
HOSE
120G, 12G, 130G, 140G, 14G, 16G, 215, 215D, 225, 227, 229, 229D, 231D, 235, 235C, 235D, 245, 245B, 245D, 350, 375, 416, 426, 613, 613C, 615, 621B, 621E, 627B, 631E, 637D, 637E, 65, 651E, 657E, 768C, 7...
120G, 12G, 130G, 140G, 14G, 16G, 215, 215D, 225, 227, 229, 229D, 231D, 235, 235C, 235D, 245, 245B, 245D, 350, 375, 416, 426, 613, 613C, 615, 621B, 621E, 627B, 631E, 637D, 637E, 65, 651E, 657E, 768C, 7...
9R2144
HOSE AS
416, 428
416, 428
120G, 130G, 140B, 14E, 3306, 815, 816, 966C, D10R, D10T, D9R
416, 428