9V9328 HOSE AS Caterpillar parts
227
Rating:
Alternative (cross code) number:
CA9V9328
9V-9328
9V9328
CA9V9328
9V-9328
9V9328
Weight: 17 pounds 7 kg.
LOGGER,
Compatible equipment models: 9V9328:
Number on catalog scheme:
37
For full view, you need register
Information:
Installation Procedure
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120H, 120H ES, 120H NA, 12G, 12H, 12H NA, 135H, 135H NA, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 3114, 3116, 3126, 3126B, 320 L, 3208, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L,...
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
10, 120, 120G, 130G, 140, 14E, 14G, 153, 16, 163, 16G, 173B, 183B, 225, 227, 235, 245, 446B, 518, 518C, 528, 572G, 583K, 594, 621, 621B, 621R, 623, 623B, 627, 627B, 631C, 631D, 633, 633C, 633D, 633E I...
227, 3304, 3408, 3412, 3412C, 3412D, 3508, 3508C, 3512, 3512B, 3516, 3516B, 3606, 3608, 3612, 3616, C280-16, G3406, PM3412, PR-1000, PR-750B
225, 227, 3406B, 3406C, 3406E, 3412, 3456, 3508, 3512, 3512B, 3516, 3606, 3608, 3612, 3616, 5230, 5230B, 776, 776C, 776D, 777, 777B, 777D, 777F, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793B, 793...
215, 225, 227, 235, 245, 3306C, 3516B, 773B, 775B, PR-450
130G, 215, 215B, 215C, 215D, 225, 227, 231D, 235, 235B, 235C, 245, 375, 375 L, 587T, 631D, 815B, 825C, 826C, 914G, 924G, 924GZ, 926, 928G, 936, 936F, 938G, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980...
227, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 641B
225, 227, 235, 235C, 245, 245B, 320B, 320B FM LL, 320B L, 320C, 322B, 322B L, 325B, 325B L, 330, 330 L, 330B, 330B L, 345B L, 350, 375, 992C, R1700 II, R1700G, R2900, R2900G
227, 235, 245, 508, 5110B, 589, 69D, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 777B, AD40, AD45, AE40, AE40 II, D9N, R1600, R1600G, R1700G
227, 235, 515, 525, 525B, 535B, 545, 814F, 815F, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 938F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980C, 980F, 980F...
9V9329
HOSE AS
227
227
8V6983
HOSE AS
227
227
9D5978
HOSE AS
120G, 12G, 130G, 227
120G, 12G, 130G, 227
7V0731
HOSE AS
227
227
7V0730
HOSE AS
227
227
9V2465
HOSE AS
227
227
6W7163
HOSE AS
FB518
FB518
6W7165
HOSE AS
FB518
FB518
6W7166
HOSE AS
FB518
FB518
6W7164
HOSE AS
FB518
FB518
6W2455
HOSE AS.
227
227
9V9397
HOSE AS
227
227