ILK8078 HOSE BARB Caterpillar parts
PR-105, PR-275
Rating:
Alternative (cross code) number:
CAILK8078
ILK-8078
ILK8078
CAILK8078
ILK-8078
ILK8078
COLD PLANER,
Number on catalog scheme:
35
For full view, you need register
Information:
Introduction
Note: The contents of the "Setup Menu" dialog are site configurable. Depending on the "Operator Configuration" settings for your system, some of the options, soft keys, or views discussed in this manual may not be accessible. Refer to your site supervisor if a specific option is not available.The AccuGrade System software displays diagnostic information about the devices detected by the software. Normally you will not need to use this function.Use the "Diagnostics" dialog to view the status of the devices connected to the AccuGrade System. Access the dialog from the "Setup Menu – Configuration" dialog.Checking the System Diagnostics
In order to access diagnostic information, complete the following steps:
From the "Setup Menu – Configuration" dialog, press the Down arrow until "Diagnostics" is highlighted.
Press the "OK" key. The Diagnostics screen appears. Refer to Illustration 1.
Illustration 1 g01261570
The screen displays a list of devices that are currently connected to the AccuGrade System. The screen also shows the current status of each of the devices. If the device is detected, the status is shown as "Connected". The device's firmware version appears in the "App" column and the device's loader version appears in the "Loader" column. If the device is not detected, the status is shown as "Not Found".Below is a list of devices that are displayed in the Diagnostics:
GPS Display
GPS Receivers
Pitch Sensor
Angle Sensors
Radio
Press the "Recheck" soft key in order to recheck whether all the system devices are connected and responding.Note: The "Recheck" soft key must be configured by your site supervisor in order for it to be displayed on the Diagnostics screen.Checking GPS Status
Press the "GPS" soft key in order to view the status of the GPS receiver and examine the quality of the GPS solution.GPS Receiver Screens
The Left receiver and Right receiver screens are similar. The following dialog shows the Left receiver screen. Refer to Illustration 2.
Illustration 2 g01261571
The first screen displayed is the left receiver screen. In order to view information for the right receiver screen, press the "Right Receiver " soft key.Note: When viewing the Right Receiver Diagnostic window, the Left receiver acts as a base for the Right receiver.Table 1 explains the fields within these dialogs.
Table 1
GPS Receiver Fields
Item Explanation
Satellites Used Number of satellites used for the current GPS position solution. The satellites must be visible at both the base station and at the machine's GPS receiver.
You need five or more satellites to initialize, and four or more to continue working.
Satellites PDOP PDOP is a quality indicator of the current GPS position solution. A small PDOP is better. The PDOP must be less than seven.
Satellites L1 Number of good quality L1 signals being received at both the base and the machine GPS receiver.
Satellites L2 Number of good quality L2 signals being received at both the base and the machine GPS receiver.
GPS Error An estimate of the current GPS error in the horizontal and vertical directions.
GPS mode Type of GPS solution.
Note: The contents of the "Setup Menu" dialog are site configurable. Depending on the "Operator Configuration" settings for your system, some of the options, soft keys, or views discussed in this manual may not be accessible. Refer to your site supervisor if a specific option is not available.The AccuGrade System software displays diagnostic information about the devices detected by the software. Normally you will not need to use this function.Use the "Diagnostics" dialog to view the status of the devices connected to the AccuGrade System. Access the dialog from the "Setup Menu – Configuration" dialog.Checking the System Diagnostics
In order to access diagnostic information, complete the following steps:
From the "Setup Menu – Configuration" dialog, press the Down arrow until "Diagnostics" is highlighted.
Press the "OK" key. The Diagnostics screen appears. Refer to Illustration 1.
Illustration 1 g01261570
The screen displays a list of devices that are currently connected to the AccuGrade System. The screen also shows the current status of each of the devices. If the device is detected, the status is shown as "Connected". The device's firmware version appears in the "App" column and the device's loader version appears in the "Loader" column. If the device is not detected, the status is shown as "Not Found".Below is a list of devices that are displayed in the Diagnostics:
GPS Display
GPS Receivers
Pitch Sensor
Angle Sensors
Radio
Press the "Recheck" soft key in order to recheck whether all the system devices are connected and responding.Note: The "Recheck" soft key must be configured by your site supervisor in order for it to be displayed on the Diagnostics screen.Checking GPS Status
Press the "GPS" soft key in order to view the status of the GPS receiver and examine the quality of the GPS solution.GPS Receiver Screens
The Left receiver and Right receiver screens are similar. The following dialog shows the Left receiver screen. Refer to Illustration 2.
Illustration 2 g01261571
The first screen displayed is the left receiver screen. In order to view information for the right receiver screen, press the "Right Receiver " soft key.Note: When viewing the Right Receiver Diagnostic window, the Left receiver acts as a base for the Right receiver.Table 1 explains the fields within these dialogs.
Table 1
GPS Receiver Fields
Item Explanation
Satellites Used Number of satellites used for the current GPS position solution. The satellites must be visible at both the base station and at the machine's GPS receiver.
You need five or more satellites to initialize, and four or more to continue working.
Satellites PDOP PDOP is a quality indicator of the current GPS position solution. A small PDOP is better. The PDOP must be less than seven.
Satellites L1 Number of good quality L1 signals being received at both the base and the machine GPS receiver.
Satellites L2 Number of good quality L2 signals being received at both the base and the machine GPS receiver.
GPS Error An estimate of the current GPS error in the horizontal and vertical directions.
GPS mode Type of GPS solution.