1272840 HOUSING Caterpillar parts
M312, M315
Rating:
Alternative (cross code) number:
CA1272840
127-2840
1272840
CA1272840
127-2840
1272840
Weight: 7 pounds 3 kg.
WHEELED EXCAVATOR,
Number on catalog scheme:
9
For full view, you need register
Information:
This diagnostic code is associated with the lift cylinders that are controlled by two solenoid valves.The Electronic Control Module (ECM) has identified more than one FMI as being responsible for a single problem.The possible causes of this diagnostic code are listed below:
The wiring harness is faulty.
The ECM generates this diagnostic code when the signal circuit is functioning correctly. This is unlikely.System Response:This failure results in diagnostic codes that are logged to the implement ECM.Test Step 1. Check The Harness And Connectors
Disconnect the machine harness connectors from the solenoid and the ECM.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0354 FMI 11 diagnostic code is active. Expected Result:The CID 0354 FMI 11 diagnostic code is active.Results:
YES - The CID 0354 FMI 11 diagnostic code is active. The problem has not been corrected. Proceed to Test Step 2.
NO - The CID 0354 FMI 11 diagnostic code is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOPTest Step 2. CHECK THE IMPLEMENT ECM
Check the circuit again. Use Cat ET, in order to perform a wiggle test on the machine wiring harness. The wiggle test can detect momentary shorts, intermittent shorts or opens in the machine wiring harness.
Check the message center for any change to the active diagnostic codes. Expected Result:No change in active diagnostic codes is generated via the wiggle test.Results:
OK - No change in active diagnostic codes is generated via the wiggle test.Repair: Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may need to be replaced. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - Changes in active diagnostic codes are generated via the wiggle test.Repair: The harness is faulty. Repair the harness or replace the harness.STOP
The wiring harness is faulty.
The ECM generates this diagnostic code when the signal circuit is functioning correctly. This is unlikely.System Response:This failure results in diagnostic codes that are logged to the implement ECM.Test Step 1. Check The Harness And Connectors
Disconnect the machine harness connectors from the solenoid and the ECM.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0354 FMI 11 diagnostic code is active. Expected Result:The CID 0354 FMI 11 diagnostic code is active.Results:
YES - The CID 0354 FMI 11 diagnostic code is active. The problem has not been corrected. Proceed to Test Step 2.
NO - The CID 0354 FMI 11 diagnostic code is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOPTest Step 2. CHECK THE IMPLEMENT ECM
Check the circuit again. Use Cat ET, in order to perform a wiggle test on the machine wiring harness. The wiggle test can detect momentary shorts, intermittent shorts or opens in the machine wiring harness.
Check the message center for any change to the active diagnostic codes. Expected Result:No change in active diagnostic codes is generated via the wiggle test.Results:
OK - No change in active diagnostic codes is generated via the wiggle test.Repair: Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may need to be replaced. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - Changes in active diagnostic codes are generated via the wiggle test.Repair: The harness is faulty. Repair the harness or replace the harness.STOP
Caterpillar parts catalog:
Parts housing Caterpillar catalog:
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215B, 225, 225D, ...
206, 212, 3054, 3054B, 3056, 307, 312, 312B L, 312C, 315, 315B L, 317, 416, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 438D, 442D, 554, 908, 91...
3054, 3056, 307, 312, 315, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, M312, M...
3054, 3054B, 3056, 3056E, 312B L, 312C, 315B L, 317, 416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914G, 924G, 924GZ, 930G, AP-655C, AP...
3054, 3054B, 3056, 3056E, 307, 312, 312B L, 312C, 315, 315B L, 317, 554, 564, 574B, 914G, AP-800C, BG-225B, BG-225C, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CP-433E, CS-4...
3054, 3056, 307, 312, 315, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, AP-800C, BG-225B, CB-434B, CB-534B, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, M312, M315, PS-200B, TH62, TH63, TH82,...
3054, 3054B, 3056, 312B L, 315B L, 416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 554, 908, AP-800C, BG-225B, BG-225C, CS-423E, M312, M315
3054, 3054B, 3056, 3056E, 312B L, 312C, 315B L, 416C, 416D, 420D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 442D, 554, 908, 924G, 924GZ, 930G, AP-655C, BB-760, BG-225C, CB-434C, CB-534C, CB-535B, CP-4...
M312, M313C, M315, M315C, M316C, M318
1550848
HOUSING-BRAKE
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
1261298
HOUSING
914G, IT14G, IT14G2, M312, M313C
914G, IT14G, IT14G2, M312, M313C
1570423
HOUSING-MOTOR
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
1068911
HOUSING AS
554, AP-800C, BG-225B, BG-225C, M312, M315
554, AP-800C, BG-225B, BG-225C, M312, M315
1306950
HOUSING
M312, M315, M318, M320
M312, M315, M318, M320
1333676
HOUSING
M312, M315, M318
M312, M315, M318
8U6417
HOUSING
205B, 206B, 211B, 212B, M312, M315, M318, M320
205B, 206B, 211B, 212B, M312, M315, M318, M320
8U7115
HOUSING
206B, 212B, M312, M315, M318, M320
206B, 212B, M312, M315, M318, M320
1401290
HOUSING
M312, M315, M318, M320
M312, M315, M318, M320
1586360
HOUSING
M312, M315
M312, M315
1253223
HOUSING
M312, M315
M312, M315
1253206
HOUSING
M312, M315
M312, M315
1253194
HOUSING
M312, M315
M312, M315
1254225
HOUSING
M312, M315
M312, M315
8U5321
HOUSING-CYLINDER
206B, 212B, M312, M313C, M315, M315C
206B, 212B, M312, M313C, M315, M315C