HOUSING-ACTUATOR 1328039 - Caterpillar

Rotation is counterclockwise when seen from drive end.Type of pump: Axial piston (variable displacement).For test, use SAE 10W oil at 65°C (150°F) Test At Full Speed:Output ... 356 liter/min (94 U.S. gpm) At a pressure of ... 690 kPa (100 psi)With pump at ... 1450 rpmWith engine at ... 2000 rpmOutput ... 341 liter/min (90 U.S. gpm) At a pressure of ... 6900 kPa (1000 psi)With pump at ... 1450 rpmWith engine at ... 2000 rpm Test At Half Speed:Output ... 178 liter/min (47 U.S. gpm) At a pressure of ... 690 kPa (100 psi)With pump at ... 725 rpmWith engine at ... 1000 rpmOutput ... 170 liter/min (45 U.S. gpm) At a pressure of ... 6900 kPa (1000 psi)With pump at ... 725 rpmWith engine at ... 1000 rpm (1) 8J2043 Spring: Length under test force ... 70.4 mm (2.77 in)Test Force ... 2900 230 N (650 52 lb)Free length after test ... 99.3 mm (3.91 in)Outside diameter ... 79.0 mm (3.11 in)(2) Shim to obtain 0.09 0.04 mm (.003 .001 in) clearance between slippers and wear plate. Check clearance at three places, 120° apart.Use shims (3) for adjustment.Shim thickness: 8J0217 ... 0.05 mm (.002 in)8J0218 ... 0.12 mm (.005 in)(4) Torque for eight bolts ... 135 20 N m (100 15 lb ft)(5) Adjust for MINIMUM swashplate angle of ... 4°0' 6'(6) Torque for nut ... 200 25 N m (150 18 lb ft)(7) Torque for two bolts ... 135 20 N m (100 15 lb ft)(8) 8J6305 Spring (outer): Length under test force ... 36.3 mm (1.43 in)Test Force ... 41 2.2 N (9.2 .5 lb)Free length after test ... 63.5 mm (2.50 in)Outside diameter ... 35.8 mm (1.41 in)(9) 8J1898 Shim: Thickness ... 0.25 mm (.010 in)One shim will change pressure ... 14 kPa (2 psi)(10) 8J3819 Spring (inner): Length under test force ... 53.1 mm (2.09 in)Test Force ... 41 2.2 N (9.2 .5 lb)Free length after test ... 69.9 mm (2.75 in)Outside diameter ... 28.4 mm (1.12 in)(11) Torque for nut ... 200 25 N m (150 18 lb ft)(12) Adjust for MAXIMUM swashplate angle of ... 14° 30' 6'(22) Torque for eight bolts ... 30 7 N m (22 5 lb ft)Shaft Bearing Setting Check
1. Do this procedure whenever shaft bearings (13) or (14), shaft (15), body (16) or head group (17) is replaced. Do not install barrel assembly or pistons for this procedure.2. Install bearing cones on shaft (15) and bearing cups in body (16) and head (17). Be sure that cups and cones are firmly seated against their locating shoulders. Bearings may be heated to 120°C (248°F) for assembly.3. Install shaft (15) in body.4. Install head (17) and gasket (18) on body. Tighten eight head bolts (4) to 135 20 N m (100 15 lb ft).5. Rotate shaft (15) with torque wrench.MAXIMUM torque required to rotate