2908705 HOUSING AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA2908705
290-8705
2908705
CA2908705
290-8705
2908705
Information:
Illustration 1 g01294600
Connections for the Test Pressure LS Travel SensorThis diagnostic code is associated with the test pressure LS travel sensor connection. This sensor connection allows service personnel to record pressure data remotely. A sensor similar to the LS travel sensor can be installed at this connection along with IQANdevelop in order to record system pressures. This connection is located near the travel valve on TK711 through TK732 machines. This connection is located near the battery box on TK741 through TK752 machines.The "Input low error" means that the IQAN-XT2 module has determined that the voltage of the sensor signal circuit is below normal. The pressure sensor sends a variable voltage input to the module that will indicate the implement pump pressure.Note: This sensor is not installed from the factory.The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is open.
The signal circuit for the sensor is shorted to the +battery circuit.
The sensor has failed.
The power circuit or the return circuit is open.
The module has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of "Input low error" for pin 38 of the IQAN-XT2 module is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK FOR POWER AT THE SENSOR
Do not disconnect the harness connector from the sensor.
At the back of the 3 contact machine harness connector for the sensor, insert 7X-1710 Multimeter Probes along supply contact 2 (wire A982-OR) and along return contact 3 (wire 975-WH) for the voltage supply.
Turn the key start switch and the disconnect switch to the ON position.
Measure the DC voltage from contact 2 to contact 3. Expected Result:The voltage measurement is 5.0 0.5 DCV.Results:
OK - The voltage measurement is 5.0 0.5 DCV. The power supply is correct. Proceed to Test Step 2.
NOT OK - The voltage measurement is less than 5.0 0.5 DCV. The voltage is not correct. There is an open or a bad connection in the circuit.Repair: There is a problem in the power supply circuit in the machine harness. Refer to the complete machine Electrical System Schematic. Check all of the connectors that are in the sensor supply circuit and the return circuit. Ensure that all connections are clean, secure and in good condition. Repair the machine harness or replace the machine harness. STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR THE SENSOR
Turn the disconnect switch and the key switch to the OFF position.
Remove the 7X-1710 Multimeter Probes from the back of the machine harness connector for the sensor.
Disconnect the machine harness connector from the sensor. At the machine harness connector for the sensor, place a jumper wire from contact 3 (wire 975-WH) to contact 1 (wire X913-BU) .
Disconnect the machine harness connector from the IQAN XT2 module.
Measure the resistance from return contact IQAN XT2 A0 -
Parts housing Caterpillar catalog:
2908234
HOUSING GP-TC
Caterpillar
Caterpillar
2907097
HOUSING AS.-
Caterpillar
Caterpillar
2906607
HOUSING-
Caterpillar
Caterpillar
2905730
HOUSING FAN
Caterpillar
Caterpillar
2902913
HOUSING - GEAR
Caterpillar
Caterpillar
2902912
HOUSING AS
Caterpillar
Caterpillar
2920656
HOUSING-COMPR
Caterpillar
Caterpillar
2915816
HOUSING FAN
Caterpillar
Caterpillar
2910567
HOUSING
Caterpillar
Caterpillar
2910498
HOUSING AS-T
Caterpillar
Caterpillar
2910232
HOUSING AS.-
Caterpillar
Caterpillar
2910231
HOUSING AS.
Caterpillar
Caterpillar