3012246 HOUSING AS-REGULATOR Caterpillar parts
C32
Rating:
Alternative (cross code) number:
CA3012246
301-2246
3012246
CA3012246
301-2246
3012246
Weight: 26 pounds 11 kg.
GENERATOR SET, MARINE ENGINE,
Compatible equipment models: 3012246:
Information:
"ECM Part Number"
The "ECM Part Number" is stored in the memory of the ECM. The "ECM Part Number" can be accessed by the use of the service tool."Software Group Part Number (Flash File)"
The part number of the flash file is programmed into the software."Software Group Release Date (Flash File)"
The release date of the flash file is programmed into the software."Software Group Description"
The "Software Group Description" lists the application."Ether Solenoid Configuration"
The parameter for the "Ether Solenoid Configuration" allows the ether solenoid to be installed or not installed."Engine Warmup Elevated Idle"
The "Engine Warmup Elevated Idle" parameter allows the operation of this feature to be enabled or disabled."Engine Retarder Enable Command"
The "Engine Retarder Enable Command" parameter allows the operation of this feature to be enabled or disabled."Security System Immobilizer Installation Status"
The "Security System Immobilizer Installation Status" allows the "security system immobilizer" to be installed or not installed."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM is installed. The parameter allows one time of programming without a factory password. In order to change the "FLS" after the initial programming, factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required. A new ECM or a blank ECM allows one time of programming of the "FTS" without the use of factory passwords. In order to change the "FTS" after the initial programming, factory passwords are required."Injector Trim File"
This parameter is for the injector trim files that are associated with each injector. If an injector is replaced or if two injectors are exchanged between cylinders, the injector trim file for the injector must be programmed to the correct cylinder.Parameter Table
Table 2
Customer Specified Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Equipment ID"     17 characters     blank     none    
"Engine Serial Number"     8 characters     blank     none    
ECM Serial Number                
ECM Part Number                
"Software Group Part Number"                
"Software Group Release Date"                
"Software Group Description"                
"Ether Solenoid Configuration"     "Not Installed" or "Continuous Flow Solenoid"     "Continuous Flow Solenoid"     none    
"Engine Warmup Elevated Idle"     "Enabled" or "Disabled"     "Enabled"     none    
"Engine Retarder Enable Command"     "Enabled" or "Disabled"     Disabled     none    
"Security System Immobilizer Installation Status"     "Installed" or "Not Installed"     "Not Installed"     none    
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory
The "ECM Part Number" is stored in the memory of the ECM. The "ECM Part Number" can be accessed by the use of the service tool."Software Group Part Number (Flash File)"
The part number of the flash file is programmed into the software."Software Group Release Date (Flash File)"
The release date of the flash file is programmed into the software."Software Group Description"
The "Software Group Description" lists the application."Ether Solenoid Configuration"
The parameter for the "Ether Solenoid Configuration" allows the ether solenoid to be installed or not installed."Engine Warmup Elevated Idle"
The "Engine Warmup Elevated Idle" parameter allows the operation of this feature to be enabled or disabled."Engine Retarder Enable Command"
The "Engine Retarder Enable Command" parameter allows the operation of this feature to be enabled or disabled."Security System Immobilizer Installation Status"
The "Security System Immobilizer Installation Status" allows the "security system immobilizer" to be installed or not installed."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM is installed. The parameter allows one time of programming without a factory password. In order to change the "FLS" after the initial programming, factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required. A new ECM or a blank ECM allows one time of programming of the "FTS" without the use of factory passwords. In order to change the "FTS" after the initial programming, factory passwords are required."Injector Trim File"
This parameter is for the injector trim files that are associated with each injector. If an injector is replaced or if two injectors are exchanged between cylinders, the injector trim file for the injector must be programmed to the correct cylinder.Parameter Table
Table 2
Customer Specified Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Equipment ID"     17 characters     blank     none    
"Engine Serial Number"     8 characters     blank     none    
ECM Serial Number                
ECM Part Number                
"Software Group Part Number"                
"Software Group Release Date"                
"Software Group Description"                
"Ether Solenoid Configuration"     "Not Installed" or "Continuous Flow Solenoid"     "Continuous Flow Solenoid"     none    
"Engine Warmup Elevated Idle"     "Enabled" or "Disabled"     "Enabled"     none    
"Engine Retarder Enable Command"     "Enabled" or "Disabled"     Disabled     none    
"Security System Immobilizer Installation Status"     "Installed" or "Not Installed"     "Not Installed"     none    
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory
Caterpillar parts catalog:
Parts housing Caterpillar catalog:
3562534
HOUSING GP-THERMOSTAT
C18, C27, C32
C18, C27, C32
7T3974
HOUSING AS-DRIVE
1090, 1190, 1190T, 120G, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA...
1090, 1190, 1190T, 120G, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA...
6N9908
HOUSING AS-TURBINE
3406, 3406B, 3406E, 3408, 3508, 3512, 3516, C15, C30, C32, G3412, G3412C, G3512, G3516
3406, 3406B, 3406E, 3408, 3508, 3512, 3516, C15, C30, C32, G3412, G3412C, G3512, G3516
3496255
HOUSING AS
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3...
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3...
3381031
HOUSING
3512C
3512C
2891198
HOUSING-COMPRESSOR
3512B, 3512C
3512B, 3512C
2755613
HOUSING
3512B, 3512C
3512B, 3512C
3023726
HOUSING
3512B, 3512C, 793F, 793F CMD, 793F OEM, 793F-XQ
3512B, 3512C, 793F, 793F CMD, 793F OEM, 793F-XQ
2981918
HOUSING-TURBINE
3512C
3512C
2769519
HOUSING-COMPRESSOR
3512B, 3512C, 793F, 793F CMD, 793F OEM, 793F-XQ, C175-16
3512B, 3512C, 793F, 793F CMD, 793F OEM, 793F-XQ, C175-16
2766456
HOUSING-TURBINE
3516B, 3516C, C175-16
3516B, 3516C, C175-16
2755622
HOUSING
3516B, 3516C
3516B, 3516C
1378241
HOUSING AS-PUMP
3516B, 3516C, 793B, 793C
3516B, 3516C, 793B, 793C
3496255
HOUSING AS
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3...
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3...
2022699
HOUSING AS
120H, 12H, 135H, 3126B, 3512, 621G, 623G, 627F, 627G, 651B, 657B, 740, 826G II, 834G, 836G, 988G, AD55, AP-1055D, AP-655C, BG-2455D, BG-260D, C18, C32, D11R, D6R II, D7R II, D8L, D8R II, D9N, D9R, G36...
120H, 12H, 135H, 3126B, 3512, 621G, 623G, 627F, 627G, 651B, 657B, 740, 826G II, 834G, 836G, 988G, AD55, AP-1055D, AP-655C, BG-2455D, BG-260D, C18, C32, D11R, D6R II, D7R II, D8L, D8R II, D9N, D9R, G36...
2872513
HOUSING
C32
C32