AVSPARE.COM
parts catalog

HOUSING-SEAL 3747013 - Caterpillar


3747013 HOUSING-SEAL Caterpillar parts
Rating:
61
Alternative (cross code) number:
CA3747013
374-7013
3747013
Caterpillar 3747013 HOUSING-SEAL
Weight: 9 pounds 4 kg.

Buy HOUSING-SEAL 3747013 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5
  For full view, you need register

Information:


Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Park the machine on a level surface with front wheels straight ahead. Lower all attachments to the ground. Apply a slight downward pressure to the attachments. Center the articulation of the machine and install the frame lock pin. The frame lock pin must move freely in the frame. Move the front wheels to vertical and install the wheel lean bolt. Engage the parking brake. Stop the engine.
Illustration 1 g01173158
Open cover (1).
Clean the area around the hydraulic oil filler cap of any dirt or debris. This must be done before the hydraulic oil filler cap can be removed.
Slowly remove the hydraulic oil filler cap in order to relieve the tank pressure.
Illustration 2 g01173167
Cutaway view
Clean the area around filter (3). This must be done before the filter can be removed.
Remove the filter with a strap type wrench. See Operation and Maintenance Manual, "Oil Filter - Inspect". Discard the used filter properly.
Clean the filter base. Check for any pieces of the seal from the old filter. Remove any pieces of the seal from the old filter.
Apply a thin coat of clean hydraulic oil to the seal of the new filter.
Install the new filter by hand until the seal of the new filter contacts the base. Note the position of the index marks on the filter in relation to a fixed point on the filter mounting base. Note: There are rotation index marks on the filter that are spaced 90 degrees or 1/4 of a turn away from each other. When you tighten the filter, use the rotation index marks as a guide.
Tighten the oil filter according to the instructions that are printed on the filter. Use the index marks as a guide for tightening the oil filter. For non-Caterpillar filters, use the instructions that are provided with the filter. Note: You may need to use a Caterpillar strap wrench, or another suitable tool, in order to turn the filter to the amount that is required for final installation. Make sure that the installation tool does not damage the filter.
Maintain the hydraulic oil level above the "MIN" mark on sight gauge (2).
Inspect the filler cap gasket. If the filler cap gasket is damaged, replace the filler cap gasket. Install the hydraulic oil filler cap.

Caterpillar parts catalog:

Caterpillar parts catalog
B20, B30 & B35 Hydraulic Hammers MAX00001-UP (MACHINE)
H115 GC S, H120 GC S, H130 GC S, H140 GC S Hydraulic Hammers HHW00001-UP (MACHINE)
H115 GC, H120 GC, H130 GC, H140 GC Hydraulic Hammers KSM00001-UP (MACHINE)


Parts housing Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.