7E5887 HOUSING GP-FUEL PUMP Caterpillar parts
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400, D400E, D8N, D8R, D8R...
Rating:
Alternative (cross code) number:
CA7E5887
7E-5887
7E5887
CA7E5887
7E-5887
7E5887
Weight: 61 pounds 27 kg.
ARTICULATED TRUCK, WHEEL TRACTOR,
Compatible equipment models: 7E5887:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
B 9U-7222 Camshaft Bearing Pilot 1
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch 1
C 9U-7223 Alignment Bushing 1
D 9U-7210 Puller Plate 1
E 9U-7213 Backup Plate 1
0S-1621 Bolt (1/2 - 13 x 1 inch) 1
F 9U-7214 Spacer Plate 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03882483
Illustration 2 g03880782
Install the No. 7 camshaft bearing (rear), as follows:
Insert the large end of Tooling (B) into the No. 7 camshaft bore.
Position Tooling (D) on Tooling (A). Install Tooling (A) in Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Illustration 3 g03883563
Illustration 4 g03883585
Orientate camshaft bearing joint (2) to Dimension (B). Dimension (B) is 20 5 degree angle above horizontal.
Refer to Illustration 4 for the correct location of oil holes (3) in camshaft bearing (1). All seven camshaft bearings (1) have the same angle.
Illustration 5 g02548921
Use Tooling (A) through Tooling (F) to pull camshaft bearing (1) into the camshaft bore. Measure the depth of the camshaft bearings from the front face of the cylinder head to the distances listed in Table 2.
Table 2
Installation Depth of Camshaft Bearing
Dimension (D) 8.0 0.5 mm (0.31 0.02 inch)
Dimension (E) 178.1 0.5 mm (7.01 0.02 inch)
Dimension (F) 349.5 0.5 mm (13.76 0.02 inch)
Dimension (G) 521.0 0.5 mm (20.51 0.02 inch)
Dimension (H) 692.4 0.5 mm (27.26 0.02 inch)
Dimension (J) 863.8 0.5 mm (34.01 0.02 inch)
Dimension (K) 1035.3 0.5 mm (40.76 0.02 inch)
Illustration 6 g03882483
Illustration 7 g03882847
Install the No. 6 through No. 2 camshaft bearings, as follows:
Insert the large end of Tooling (B) into the camshaft bore.Note: Use Tooling (C) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (C) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B).
Install Tooling (A) in Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Refer to Step 1.d through Step 1.f for the correct orientation and proper installation depth of camshaft bearing (1).
Use Tooling (A) to pull camshaft bearing (1) into the camshaft bore.
Illustration 8 g03882483
Illustration 9 g03882848
Install the No. 1 camshaft bearing (front), as follows:
Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (C) on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Refer to Step 1.d through Step 1.f for the correct orientation and proper installation depth of camshaft bearing (1).
Use Tooling (A) to pull camshaft bearing (1) into the No. 1 camshaft bore.End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
B 9U-7222 Camshaft Bearing Pilot 1
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch 1
C 9U-7223 Alignment Bushing 1
D 9U-7210 Puller Plate 1
E 9U-7213 Backup Plate 1
0S-1621 Bolt (1/2 - 13 x 1 inch) 1
F 9U-7214 Spacer Plate 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03882483
Illustration 2 g03880782
Install the No. 7 camshaft bearing (rear), as follows:
Insert the large end of Tooling (B) into the No. 7 camshaft bore.
Position Tooling (D) on Tooling (A). Install Tooling (A) in Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Illustration 3 g03883563
Illustration 4 g03883585
Orientate camshaft bearing joint (2) to Dimension (B). Dimension (B) is 20 5 degree angle above horizontal.
Refer to Illustration 4 for the correct location of oil holes (3) in camshaft bearing (1). All seven camshaft bearings (1) have the same angle.
Illustration 5 g02548921
Use Tooling (A) through Tooling (F) to pull camshaft bearing (1) into the camshaft bore. Measure the depth of the camshaft bearings from the front face of the cylinder head to the distances listed in Table 2.
Table 2
Installation Depth of Camshaft Bearing
Dimension (D) 8.0 0.5 mm (0.31 0.02 inch)
Dimension (E) 178.1 0.5 mm (7.01 0.02 inch)
Dimension (F) 349.5 0.5 mm (13.76 0.02 inch)
Dimension (G) 521.0 0.5 mm (20.51 0.02 inch)
Dimension (H) 692.4 0.5 mm (27.26 0.02 inch)
Dimension (J) 863.8 0.5 mm (34.01 0.02 inch)
Dimension (K) 1035.3 0.5 mm (40.76 0.02 inch)
Illustration 6 g03882483
Illustration 7 g03882847
Install the No. 6 through No. 2 camshaft bearings, as follows:
Insert the large end of Tooling (B) into the camshaft bore.Note: Use Tooling (C) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (C) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B).
Install Tooling (A) in Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Refer to Step 1.d through Step 1.f for the correct orientation and proper installation depth of camshaft bearing (1).
Use Tooling (A) to pull camshaft bearing (1) into the camshaft bore.
Illustration 8 g03882483
Illustration 9 g03882848
Install the No. 1 camshaft bearing (front), as follows:
Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (C) on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (F) and Tooling (E) on Tooling (B).
Refer to Step 1.d through Step 1.f for the correct orientation and proper installation depth of camshaft bearing (1).
Use Tooling (A) to pull camshaft bearing (1) into the No. 1 camshaft bore.End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Cat SIS web machinery list:
Parts housing Caterpillar catalog:
3V3855
HOUSING-BEARING SUPPORT
980C, 980F, D35C, D35HP, D44B, D550B
980C, 980F, D35C, D35HP, D44B, D550B
3T4384
HOUSING AS-CLUTCH
814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, R1600, R1600G, R1600H, R1700 II, R1700G
814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, R1600, R1600G, R1600H, R1700 II, R1700G
3V6697
HOUSING
824C, 980C, 980F, 980F II, R1700 II
824C, 980C, 980F, 980F II, R1700 II
9V2411
HOUSING-BEARING
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
9V2410
HOUSING-BEARING
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
8P0955
HOUSING
814B, 815B, 966D
814B, 815B, 966D
8V7885
HOUSING-SUPPORT
814B, 815B, 816B, 966D, 966F, 966G
814B, 815B, 816B, 966D, 966F, 966G
8V7884
HOUSING-SUPPORT
814B, 815B, 816B, 966D, 966F, 966G, D25D, D350E, D400E, D40D
814B, 815B, 816B, 966D, 966F, 966G, D25D, D350E, D400E, D40D
5S4326
HOUSING-SCREEN
AD30, AD55, D250D, D300D, D350E, D350E II, D400, D400E, D400E II, D40D
AD30, AD55, D250D, D300D, D350E, D350E II, D400, D400E, D400E II, D40D
8D9973
HOUSING
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H, 16H NA
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H, 16H NA
3P7042
HOUSING-CLUTCH
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA
5T7127
HOUSING
16G, 16H, 16H NA
16G, 16H, 16H NA
8N9680
HOUSING AS-GOVERNOR
16G, 16H NA, 245, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II,...
16G, 16H NA, 245, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II,...
7W4247
HOUSING AS-GOVERNOR
16G, 16H NA, 245, 3406B, 3406C, 375, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II, HT400, PM-46...
16G, 16H NA, 245, 3406B, 3406C, 375, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II, HT400, PM-46...
1017769
HOUSING-COMPRESSOR
3406B, 3406C, 3408C, 3412E, 589, 657E, 769C, 771C, 834B, 836, 988B, 988F II, C-15, HT400, PM-465, RM-350B, SM-350
3406B, 3406C, 3408C, 3412E, 589, 657E, 769C, 771C, 834B, 836, 988B, 988F II, C-15, HT400, PM-465, RM-350B, SM-350
9Y7632
HOUSING-COMPRESSOR
3406B, 3406C
3406B, 3406C
7N6183
HOUSING AS-TURBINE
3406, 3406B, 3406C
3406, 3406B, 3406C
8N8098
HOUSING
16H NA, 245, 3406, 3406B, 3406C, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980G, D350E, D400E, D8N, D8R, D8R II, HT400, PM-465, RM-250C, RM-3...
16H NA, 245, 3406, 3406B, 3406C, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980G, D350E, D400E, D8N, D8R, D8R II, HT400, PM-465, RM-250C, RM-3...
1411017
HOUSING
3406E
3406E
1243401
HOUSING
3406E, C15, C18
3406E, C15, C18
1243402
HOUSING
3406E, C15, C18
3406E, C15, C18
1283854
HOUSING AS-FRONT
3406E, 3456, 621G, 623G, 627F, 627G, 657B, 834G, 836G, 988G, D350E II, D400E II, PM3456, R2900
3406E, 3456, 621G, 623G, 627F, 627G, 657B, 834G, 836G, 988G, D350E II, D400E II, PM3456, R2900
4N8242
HOUSING-SHUTOFF
3406, 3408, 3408C, 3412, 3412C
3406, 3408, 3408C, 3412, 3412C
7N7622
HOUSING AS-GOVERNOR
3408, 3408B, 3408C, 3412, 3412C
3408, 3408B, 3408C, 3412, 3412C