7G4281 HOUSING AS-SUPPORT Caterpillar parts
613C, 613C II, 613G, 936, 936F, 950B, 950B/950E, 950F, 950F II, 966C, G936, R1300, R1300G
Rating:
Alternative (cross code) number:
CA7G4281
7G-4281
7G4281
CA7G4281
7G-4281
7G4281
Weight: 64 pounds 29 kg.
LOAD HAUL DUMP, WHEEL TRACTOR-SCRAPER,
Related part:
7G4281
HSG AS-SPRT-YM
2977201
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
7G4281 HOUSING A (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Fits equipment: ENGINE - MACHINE: 3116, 3126, 3208, C6.6; WHEEL-TYPE LOADER: 950F, 950F II; WHEEL TRACTOR-SCRAPER: 613C, 613C II, 613G. ENGINE - MACHINE: 3116, 3126, 3208, C6.6; WHEEL-TYPE LOADER: 950F, 950F II; WHEEL TRACTOR-SCRAPER: 613C, 613C II, 613G. || Condition: NEW AFTERMARKET || Weight: 70.4 lbs || Dimensions: 10-15.16-15.16 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Fits equipment: ENGINE - MACHINE: 3116, 3126, 3208, C6.6; WHEEL-TYPE LOADER: 950F, 950F II; WHEEL TRACTOR-SCRAPER: 613C, 613C II, 613G. ENGINE - MACHINE: 3116, 3126, 3208, C6.6; WHEEL-TYPE LOADER: 950F, 950F II; WHEEL TRACTOR-SCRAPER: 613C, 613C II, 613G. || Condition: NEW AFTERMARKET || Weight: 70.4 lbs || Dimensions: 10-15.16-15.16 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
CTP 7G4281 Iron and Steel Cast Housing for Model 613C/613C II/613G/936/936F/950B/950B/950E/950F/950F II
CTP For Model 613C/613C II/613G/936/936F/950B/950B/950E/950F/950F II || Sold in each || Easy in-and-out fit
CTP For Model 613C/613C II/613G/936/936F/950B/950B/950E/950F/950F II || Sold in each || Easy in-and-out fit
7G4281 HOUSING A (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 70.4 lbs || Dimensions: 10-16.68-16.68 in || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 70.4 lbs || Dimensions: 10-16.68-16.68 in || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
Number on catalog scheme:
23
For full view, you need register
Compatible equipment models: 7G4281:
Information:
All Caterpillar Engines Equipped With A TurbochargerBe sure to correctly tighten the clamp assemblies that fasten the compressor housing and turbine housing to the cartridge. If a clamp assembly becomes loose, a housing may contact the compressor wheel or turbine wheel. This could result in damage to the turbocharger components. Use the procedure that follows to install the clamp assemblies. Make a note of this procedure in the appropriate Service Manual Disassembly and Assembly modules.
1. Be sure the clamp assemblies are correctly located on the housings and the cartridge. Be sure the housings are correctly oriented on the cartridge. Then tighten each clamp assembly nut or bolt to the specified torque.2. Lightly tap all around the outside of each clamp assembly with a soft hammer to be sure it is seated.3. Again, tighten each clamp assembly nut or bolt to the specified torque.4. Repeat Steps 2 and 3 until each clamp assembly nut or bolt does not turn when the specified torque is applied.
Location of clamp assemblies.
1. Be sure the clamp assemblies are correctly located on the housings and the cartridge. Be sure the housings are correctly oriented on the cartridge. Then tighten each clamp assembly nut or bolt to the specified torque.2. Lightly tap all around the outside of each clamp assembly with a soft hammer to be sure it is seated.3. Again, tighten each clamp assembly nut or bolt to the specified torque.4. Repeat Steps 2 and 3 until each clamp assembly nut or bolt does not turn when the specified torque is applied.
Location of clamp assemblies.
Caterpillar parts catalog:
Parts housing Caterpillar catalog:
508, 518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
936, 936F, 950B, 950B/950E, 950F, 950F II, 966C, G936
936F, D250D
936F, 950F, 950F II, 960F
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
950F, 950F II
950F
950F, 950F II, 960F
950F II, 960F, 966C
8D2551
HOUSING AS
613, 613B, 613C, 613C II, 613G
613, 613B, 613C, 613C II, 613G
7V9634
HOUSING-BEARING SUPPORT
613C, 613C II, 613G
613C, 613C II, 613G
7T3641
HOUSING-LINKAGE
613C, 615
613C, 615
9G7349
HOUSING
613C, 615
613C, 615
1274368
HOUSING-AXLE
613C, 613C II
613C, 613C II
5T1116
HOUSING AS
651E
651E
5T1992
HOUSING
613, 613C
613, 613C
2T1071
HOUSING-LAMP
613C, 615, 615C
613C, 615, 615C
3T0750
HOUSING AS
613C, 615, 615C
613C, 615, 615C
9J3441
HOUSING
613C, 613C II, 613G, 623B, 633D
613C, 613C II, 613G, 623B, 633D
613C, 613C II, 613G, 936, 936F, 950B, 950B/950E, 950F, 950F II, 960F, 966C, G936, R1300, R1300G
9G5809
HOUSING-CLUTCH
613C, 613C II, 613G
613C, 613C II, 613G