7S8497 HOUSING ASSEM. Caterpillar parts
518, 518C, 528, 528B, 530B, 920, 930
Rating:
Alternative (cross code) number:
CA7S8497
7S-8497
7S8497
CA7S8497
7S-8497
7S8497
Weight: 25 pounds 11 kg.
WHEEL LOADER, WHEEL SKIDDER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 7S8497:
Information:
This procedure alleviates the need for the "H" bar to hold down liners during projection measurements.
Liner Projection Components
(1) Bolt. (2) Washer. (3) Washer. Install clean liners or cylinder packs (without the filler band or the rubber seals), spacer plate gasket and clean spacer plate. Install bolts and washers, as indicated previously, in the holes. Install all bolts or the six bolts around the liner. Tighten the bolts to a torque of 95 N m (70 lb ft).Use the 8T0455 Liner Projection Tool Group to measure liner projection at positions indicated with an A, B, C and D. Record measurements for each cylinder. Add the four readings for each cylinder and divide by four to find the average. If the liner projections are out of specification, try rotating the liner or install the liner in another bore to see if the measurements improve.If the liner projections are all below the specifications or low in the range, 0.025 mm (0.001 in) or 0.051 mm (0.002 in), try using a thinner spacer plate (6I3189 or 6I4303). These plates are 0.076 mm (0.003 in) thinner than the regular plate and they will increase the liner projection, thus increasing the fire ring crush. Use these spacer plates to compensate for low liner projections that are less than 0.076 mm (0.003 in) or if the inspection of the top deck reveals no measurable damage directly under the liner flanges, but the average liner projection is less than 0.076 mm (0.003 in).Do not exceed the maximum liner projection of 0.152 mm (0.006 in). Excessive liner projection will contribute to liner flange cracking.With the proper liner projection, mark the liners in the proper position and set them aside.When the engine is ready for final assembly, the O-ring seals, cylinder block and upper filler band must be lubricated before installation. Apply clean engine oil immediately before assembly. If applied too early, the seals may swell and be pinched under the liners during installation.
Liner Projection Components
(1) Bolt. (2) Washer. (3) Washer. Install clean liners or cylinder packs (without the filler band or the rubber seals), spacer plate gasket and clean spacer plate. Install bolts and washers, as indicated previously, in the holes. Install all bolts or the six bolts around the liner. Tighten the bolts to a torque of 95 N m (70 lb ft).Use the 8T0455 Liner Projection Tool Group to measure liner projection at positions indicated with an A, B, C and D. Record measurements for each cylinder. Add the four readings for each cylinder and divide by four to find the average. If the liner projections are out of specification, try rotating the liner or install the liner in another bore to see if the measurements improve.If the liner projections are all below the specifications or low in the range, 0.025 mm (0.001 in) or 0.051 mm (0.002 in), try using a thinner spacer plate (6I3189 or 6I4303). These plates are 0.076 mm (0.003 in) thinner than the regular plate and they will increase the liner projection, thus increasing the fire ring crush. Use these spacer plates to compensate for low liner projections that are less than 0.076 mm (0.003 in) or if the inspection of the top deck reveals no measurable damage directly under the liner flanges, but the average liner projection is less than 0.076 mm (0.003 in).Do not exceed the maximum liner projection of 0.152 mm (0.006 in). Excessive liner projection will contribute to liner flange cracking.With the proper liner projection, mark the liners in the proper position and set them aside.When the engine is ready for final assembly, the O-ring seals, cylinder block and upper filler band must be lubricated before installation. Apply clean engine oil immediately before assembly. If applied too early, the seals may swell and be pinched under the liners during installation.
Caterpillar parts catalog:
Parts housing Caterpillar catalog:
7C9304
HOUSING-TURBINE
12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 3306, 528B, 530B, D6H, D6H XL, D6H XR, D7H
12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 3306, 528B, 530B, D6H, D6H XL, D6H XR, D7H
7N1687
HOUSING
120G, 130G, 215B, 225, 3304, 3304B, 518, 518C, 936F, 950B, 963, CB-534, CS-643, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, E240
120G, 130G, 215B, 225, 3304, 3304B, 518, 518C, 936F, 950B, 963, CB-534, CS-643, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, E240
6N8413
HOUSING-PUMP
140B, 1673C, 215, 3304, 920, 930, 941, 950, 977K, D4D, D5, D6C, G3306
140B, 1673C, 215, 3304, 920, 930, 941, 950, 977K, D4D, D5, D6C, G3306
1T1987
HOUSING-ROTATING
517, 518, 518C, 613C, 613C II, 930R, 966C, D4H XL, D4HTSK III
517, 518, 518C, 613C, 613C II, 930R, 966C, D4H XL, D4HTSK III
4S8682
HOUSING ASSEM.
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D, D4E
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D, D4E
8S6197
HOUSING ASSEM.
518, 528, 920, 930, 941, 951B, D4D, D4E
518, 528, 920, 930, 941, 951B, D4D, D4E
2P4404
HOUSING ASSEM.
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D
1T0024
HOUSING
518, 613, 613B, 920, 930, 936, 950, 955H, 966C, 966R, G936
518, 613, 613B, 920, 930, 936, 950, 955H, 966C, 966R, G936
6K0053
HOUSING
508, 518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
508, 518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
1V1080
HOUSING
528, 613, 613B, 814, 815, 950, 966C
528, 613, 613B, 814, 815, 950, 966C
3V7427
HOUSING ASSEM.
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
518, 518C, 528, 528B, 530B, 814, 920, 930, 930R, 950, 966C, 966R, 980B, 992, FB518
1T1009
HOUSING ASSEM.
518C, 528, 528B, 530B, 814, 815, 816, 950B, 950B/950E
518C, 528, 528B, 530B, 814, 815, 816, 950B, 950B/950E
5D5416
HOUSING ASSEM.
621, 623, 627
621, 623, 627
9M2413
HOUSING
16, 631C, 657, 666, 769, 824B, 825B, 834, 988
16, 631C, 657, 666, 769, 824B, 825B, 834, 988
5S6732
HOUSING ASSEM.
621, 980
621, 980
8S3463
HOUSING
627, 627B, 637B, 637D
627, 627B, 637B, 637D
8S3455
HOUSING ASSEM.
627, 627B, 637B, 637D
627, 627B, 637B, 637D
6K9963
HOUSING
926, 930, 930R, IT28
926, 930, 930R, IT28
6K9964
HOUSING
518, 926, 930, 930R, IT28
518, 926, 930, 930R, IT28
5D5509
HOUSING ASSEM.
621, 623, 627
621, 623, 627