9G4351 HOUSING-RECEPTACLE Caterpillar parts
30/30, 330, 330 L, 350, 3516B, 375, 5130B, 5230, 5230B, 527, 75C, 776D, 777, 777B, 777C, 777D, 784C, 785C, 785D, 789C, 793C, 914G, 916, 918F, 924F, 924G, 926, 928G, 936, 936F, 938F, 950F, 966F, 966G, ...
Rating:
Alternative (cross code) number:
CA9G4351
9G-4351
9G4351
CA9G4351
9G-4351
9G4351
Weight: 0.010 pounds 0 kg.
ARTICULATED TRUCK, WHEEL LOADER,
Compatible equipment models: 9G4351:
Information:
Illustration 1 g01320849
Schematic of the Blade Control Handle BaseThis diagnostic code is associated with the Blade Control Handle Lift Position sensor (Y-axis). The FMI 08 diagnostic means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range. The sensor is a PWM sensor that operates at a frequency of approximately 500 hertz. The sensor has an operating duty cycle of 5% to 95%. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1078 FMI 08 is active before performing this procedure.Note: Use a Digital Multimeter for the measurements in this procedure. System Response:A level 1 warning will be generated. The feature is disabled.Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact 1 (wire 709-OR) for the voltage supply.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact 2 (wire J764-BR) for the ground.
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact 1 (wire 709-OR) to contact 2 (wire J764-BR).Expected Result:The voltage is 10 0.5 DCV.Results:
Cat SIS web machinery list:
Parts housing Caterpillar catalog:
9V2410
HOUSING-BEARING
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
1005879
HOUSING
950F, 950F II
950F, 950F II
1T1850
HOUSING AS
950F
950F
1T1940
HOUSING AS
950F, 950F II, 960F
950F, 950F II, 960F
1308706
HOUSING-PINION
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K
8V7885
HOUSING-SUPPORT
814B, 815B, 816B, 966D, 966F, 966G
814B, 815B, 816B, 966D, 966F, 966G
8V7884
HOUSING-SUPPORT
814B, 815B, 816B, 966D, 966F, 966G, D25D, D350E, D400E, D40D
814B, 815B, 816B, 966D, 966F, 966G, D25D, D350E, D400E, D40D
9Y8270
HOUSING
776C, 777B, D11N
776C, 777B, D11N
1060818
HOUSING AS
785, 785B, 785C, 785D
785, 785B, 785C, 785D
5S4326
HOUSING-SCREEN
AD30, AD55, D250D, D300D, D350E, D350E II, D400, D400E, D400E II, D40D
AD30, AD55, D250D, D300D, D350E, D350E II, D400, D400E, D400E II, D40D
0551260
HOUSING-BRAKE
CP-563, CS-531C, CS-531D, CS-533, CS-533C, CS-533D, CS-563C, CS-563D, CS-573C, CS-573D, CS-583, CS-583C, CS-583D
CP-563, CS-531C, CS-531D, CS-533, CS-533C, CS-533D, CS-563C, CS-563D, CS-573C, CS-573D, CS-583, CS-583C, CS-583D
4P8733
HOUSING
D8L, D9N, D9R
D8L, D9N, D9R
1164700
HOUSING AS
65C, 65E, 75C, 75D, 75E, 784B, 785B, 789B, 793B, 793C, 85C, 85D
65C, 65E, 75C, 75D, 75E, 784B, 785B, 789B, 793B, 793C, 85C, 85D
1450847
HOUSING AS
5130, 5130B, 5230, 5230B, 65C, 65E, 75C, 75D, 75E, 770, 772, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797, 797B, 85C, 85D, 85E, 933C, 939C, 95E, D3C III, D4C III, D5C III, RM-300, RM-500,...
5130, 5130B, 5230, 5230B, 65C, 65E, 75C, 75D, 75E, 770, 772, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797, 797B, 85C, 85D, 85E, 933C, 939C, 95E, D3C III, D4C III, D5C III, RM-300, RM-500,...
4E1276
HOUSING
75C, 75D, 85C, 85D
75C, 75D, 85C, 85D
1073579
HOUSING-TURBINE
3176B, 3176C, 480, 65E, 75C, 75D, 75E, 85C, C-10, R1700 II
3176B, 3176C, 480, 65E, 75C, 75D, 75E, 85C, C-10, R1700 II
4P2875
HOUSING-COMPRESSOR
3176, 3176B, 3176C, 75, 75C, 814F, 815F, 816F, 85C, 966F II, 970F, 972G, 973, 973C, C-10, R1600, R1700 II, R1700G
3176, 3176B, 3176C, 75, 75C, 814F, 815F, 816F, 85C, 966F II, 970F, 972G, 973, 973C, C-10, R1600, R1700 II, R1700G
1067156
HOUSING AS
65C, 75, 75C, 75D, 85C, 85D
65C, 75, 75C, 75D, 85C, 85D
8E6627
HOUSING-CLUTCH
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
1054364
HOUSING-CLUTCH
65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
6Y1301
HOUSING-IDLER
65, 65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65, 65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E
7T4802
HOUSING
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
7T4803
HOUSING
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 95E
1729874
HOUSING
65C, 65E, 75C, 75D, 75E, 85D, 85E, 95E
65C, 65E, 75C, 75D, 75E, 85D, 85E, 95E