2F8087 HUB Caterpillar parts
Rating:
Alternative (cross code) number:
CA2F8087
2F-8087
2F8087
CA2F8087
2F-8087
2F8087
Weight: 5 pounds 2 kg.
Information:
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00945551
Position spacers (9) and spring washers (10) to piston (7).
Illustration 2 g00945550
Install cover (4) to piston (7).
Spring force is created when releasing the brakes. Failure to follow the recommended procedure could cause the threads inside the brake piston to fail and forcefully propel the tooling. Personal injury or death could result from being struck by tooling propelled by the released spring force. Follow the recommended procedure when releasing the brakes.
Illustration 3 g00945548
Install Tooling (B) to put the brake in the released position. Follow the following procedure to put the brake in the released position.
Modify the forcing bolt for Tooling (B) to make the threads 90.00 mm (3.543 inch) in length.
Install Tooling (B) to the brake.
Make sure that the forcing bolt that is used in Tooling (B) has full thread engagement into the brake.Note: Do not overtighten the threads.
To release the brake, hold the forcing bolt stationary and turn the nut in the clockwise direction. The nut will be tightened to a torque of approximately 340 N m (250 lb ft) to release the brake.
Illustration 4 g00945545
Install O-ring seal (8) to cover (4).
Install O-ring seal (6) to piston (7).
Illustration 5 g00945544
Install brake disc kit (5).
Illustration 6 g00945542
Install Tooling (C).
Use two people to position cover (4) to the machine. The weight of cover (4) is approximately 36 kg (80 lb).
Install bolts (3) to cover (4).
Remove Tooling (C).
Illustration 7 g00945540
Install remaining bolts (3) to cover (4).
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 8 g00945534
Use Tooling (B) to relieve the spring force. Hold the forcing bolt stationary and turn the nut in the counterclockwise direction. Remove Tooling (B).
Illustration 9 g00945529
Install plug (2).
Illustration 10 g00945526
Install cover (1).
Illustration 11 g06299795
Typical Example
The wheels have been removed for photographic clarity.
Remove Tooling (A).
Remove Tooling (D). Refer to Tool Operating Manual, NEHS1303 , "Lift Group (Stand - 25 Ton)" for more information on Tooling (D).
Parts hub Caterpillar catalog:
2F6377
HUB A.
Caterpillar
Caterpillar
2F5908
HUB
Caterpillar
Caterpillar
2F5877
HUB A.
Caterpillar
Caterpillar
2F3570
HUB
Caterpillar
Caterpillar
2F3088
HUB
Caterpillar
Caterpillar
2F3080
HUB
Caterpillar
Caterpillar
2H4640
HUB
Caterpillar
Caterpillar
2H2720
HUB
Caterpillar
Caterpillar
2H0934
HUB A.
Caterpillar
Caterpillar
2G6164
HUB OUTER
Caterpillar
Caterpillar
2G5343
HUB
Caterpillar
Caterpillar
2F8089
HUB A WHEEL
Caterpillar
Caterpillar