3793897 HUB Caterpillar parts
Rating:
Alternative (cross code) number:
CA3793897
379-3897
3793897
CA3793897
379-3897
3793897
Weight: 29 pounds 13 kg.
This part in 2 request:
Show.
This information for suppliers only!
2024-05-15
2024-04-14
Information:
Installation Procedure
(1) Put 5P2948 Connector (1) in ether valve (2). Install ether valve (2) in a good location, as follows: A. Install in a vertical position that is within the angle limit shown.B. As near the engine manifold as possible, but not on the engine.C. Do not install the ether valve in a location where the temperature is more than 93°C (200°F).(2) Install 7N2059 Clamp (3) directly above ether valve (2) according to the dimension shown. According to the ether starting air group that is to be installed, the part number of the atomizer will be either 6N7672 or 6N9995, and will look like item (9) in one of the above illustrations. When either atomizer is installed on an engine, the arrow [(F) or (G)] must be put in a specific position for each engine model. This instruction gives the correct position of the arrow for all engines.It is necessary to remove a 1/4" pipe plug from the air inlet system of the engine to install an atomizer (9). A 6N5899 Temperature Switch must also be installed, after a 3/8" pipe plug is removed from the cylinder head. See the information that follows for the location of the plugs to remove for installation of the temperature switch and an atomizer (9).3406 Turbocharged - Industrial, Marine, Marine Auxiliary, Truck
TOP VIEW
REAR VIEW(1) Inlet manifold, (2) cylinder head, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is toward either the front or rear of the engine.3406 Turbocharged, Aftercooled - Industrial, Truck
TOP VIEW
REAR VIEW(1) Inlet manifold, (2) cylinder head, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is down.3406 Turbocharged, Aftercooled - Marine, Marine Auxiliary
TOP VIEW
REAR VIEW(1) Aftercooler, (2) air inlet pipe, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is toward aftercooler (1).3408 Turbocharged - Industrial, Marine, Marine Auxiliary
TOP VIEW
RIGHT SIDE VIEW(1)
(1) Put 5P2948 Connector (1) in ether valve (2). Install ether valve (2) in a good location, as follows: A. Install in a vertical position that is within the angle limit shown.B. As near the engine manifold as possible, but not on the engine.C. Do not install the ether valve in a location where the temperature is more than 93°C (200°F).(2) Install 7N2059 Clamp (3) directly above ether valve (2) according to the dimension shown. According to the ether starting air group that is to be installed, the part number of the atomizer will be either 6N7672 or 6N9995, and will look like item (9) in one of the above illustrations. When either atomizer is installed on an engine, the arrow [(F) or (G)] must be put in a specific position for each engine model. This instruction gives the correct position of the arrow for all engines.It is necessary to remove a 1/4" pipe plug from the air inlet system of the engine to install an atomizer (9). A 6N5899 Temperature Switch must also be installed, after a 3/8" pipe plug is removed from the cylinder head. See the information that follows for the location of the plugs to remove for installation of the temperature switch and an atomizer (9).3406 Turbocharged - Industrial, Marine, Marine Auxiliary, Truck
TOP VIEW
REAR VIEW(1) Inlet manifold, (2) cylinder head, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is toward either the front or rear of the engine.3406 Turbocharged, Aftercooled - Industrial, Truck
TOP VIEW
REAR VIEW(1) Inlet manifold, (2) cylinder head, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is down.3406 Turbocharged, Aftercooled - Marine, Marine Auxiliary
TOP VIEW
REAR VIEW(1) Aftercooler, (2) air inlet pipe, (A) location for atomizer (3), (B) location for temperature switch. Install atomizer (3) so the arrow at location (C) is toward aftercooler (1).3408 Turbocharged - Industrial, Marine, Marine Auxiliary
TOP VIEW
RIGHT SIDE VIEW(1)
Caterpillar parts catalog:
Parts hub Caterpillar catalog:
5195689
HUB GP-DRIVE
Caterpillar
Caterpillar
5195688
HUB GP-DRIVE
Caterpillar
Caterpillar
4863252
HUB
Caterpillar
Caterpillar
4556012
HUB
Caterpillar
Caterpillar
5262179
HUB-DRUM
Caterpillar
Caterpillar
5262178
HUB-DRUM
Caterpillar
Caterpillar
4555971
HUB
Caterpillar
Caterpillar
4532038
HUB-TURBINE
Caterpillar
Caterpillar
4532030
HUB-IMPELLER
Caterpillar
Caterpillar
4526698
HUB-IMPELLER
Caterpillar
Caterpillar
4421904
HUB-BRAKE
Caterpillar
Caterpillar
3810839
HUB
Caterpillar
Caterpillar