AVSPARE.COM
parts catalog

HUB-CLUTCH 5088229 - Caterpillar



5088229 HUB-CLUTCH Caterpillar parts HUB
Rating:
61
Alternative (cross code) number:
CA5088229
508-8229
5088229
Caterpillar 5088229 HUB-CLUTCH

Buy HUB-CLUTCH 5088229 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Probable Causes
Engine shutdown switches
Circuit breakers
Machine security system
Battery cables and/or battery
Starting motor solenoid or starting circuit
Starting motor and/or flywheel ring gear
Electrical power supply
Internal engine problemRecommended Repairs
Engine Shutdown Switches (If Equipped)
Verify that there are no active shutdown switches.Circuit Breakers
Check the state of each of the circuit breakers. Reset the circuit breakers if the circuit breakers are tripped. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip. Make any necessary repairs.Machine Security System
Verify that the correct keyswitch is being used. Turn the keyswitch to the ON position.
Use the electronic service tool in order to check if diagnostic code 1639-09 is active. Verify that the lamp for the machine security system is on.
If diagnostic code 1639-09 is active, the machine security system is armed. Deactivate the machine security system and try to start the engine.
If the engine will not start, use the electronic service tool to check for logged diagnostic codes.
Make repairs for all diagnostic codes. Ensure that the repair has eliminated the fault.
If there are no active diagnostic codes, refer to the Troubleshooting Manual for your machine application. Battery Cables and/or Battery
Inspect the main power switch, battery posts, and battery cables for loose connections and corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Clean the battery posts. Replace the cables. Tighten any loose connections.
Inspect the battery.
Charge the battery.
Load test the battery. Refer to Systems Operation, Testing and Adjusting, "Battery - Test". Starting Motor Solenoid or Starting Circuit
Test the operation of the starting motor solenoid. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Check the wiring to the starting motor solenoid. Starting Motor and/or Flywheel Ring Gear
Test the operation of the starting motor. Check the wiring for the starting motor. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Inspect the pinion on the starting motor and the flywheel ring gear for damage. Electrical Power Supply
If there is no electrical power supply, investigate the cause and rectify any defects. Refer to Systems Operation, Testing and Adjusting, "Charging System - Test".Internal Engine Problem
Remove the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
Attempt to rotate the crankshaft through 360 degrees in both direction. If the crankshaft rotates correctly but fluid is expelled from the hole for the glow plug, investigate the cause of the fluid in the cylinder.
If the crankshaft rotates correctly and no fluid is expelled, install the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
If the engine does not rotate in Step 2, disassemble the engine. Refer to Disassembly and Assembly.
Inspect the internal components for the following conditions:
Seizure
Broken components
Bent components


Parts hub Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.