2583183 HYDRAULIC AR Caterpillar parts
262C, 262C2, 287C, 287C2, 289C, 289C2
Rating:
Alternative (cross code) number:
CA2583183
258-3183
2583183
CA2583183
258-3183
2583183
COMPACT TRACK LOADER, SKID STEER LOADER,
Compatible equipment models: 2583183:
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar SIS
262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engine »
258-3183
HYDRAULIC AR
287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engine »
258-3183
HYDRAULIC AR
289C Compact Track Loader JMP00001-UP (MACHINE) POWERED BY 3044C Engine »
258-3183
HYDRAULIC AR
262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine »
258-3183
HYDRAULIC AR
287C2 Multi Terrain Loader SSB00001-UP (MACHINE) POWERED BY C3.4 Engine »
258-3183
HYDRAULIC AR
289C2 Compact Track Loader RTD00001-UP (MACHINE) POWERED BY C3.4 Engine »
258-3183
HYDRAULIC AR
Caterpillar parts catalog:
Information:
Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.Machine Preparation
Illustration 4 g06033632
Flow meter tool layout
Tooling (D)
( 1) Auxiliary pump
(2) Delivery line for auxiliary pump
(3) Makeup line
(4) Seal
(5) Elbow
(6) Swing motorAuxiliary Pump
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 5 g06032484
Pump compartment
(1) Auxiliary pump
(2) Delivery line for auxiliary pump
Position the machine on level ground.
Stop the engine.
Release pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 5.
Disconnect delivery line (2) from auxiliary pump (1).
Install seal (D16) and plug (D15) to the end of the delivery line (2).
Assemble and install seal (D14), coupling (D13), seals (D4), fitting (D12), seal (D11), fitting (D10), and fitting (D5) on the auxiliary pump.
Illustration 6 g06033643
Swing motor (top view)
(3) Makeup line
(4) Seal
(5) Elbow
Disconnect makeup line (3) from elbow (5) at the swing motor.
Assemble and install seals (D18), tee (D19), adapter (D17), seal (D4), and fitting (D5) to elbow (5) at the swing motor.
Install seal (4) and makeup line (3) to tee (D19).
Remove 311-1362 Vacuum Cap and install the filler plug for the hydraulic tank.
Connect portable hydraulic tester (D) and test hoses between coupling assembly at the auxiliary pump and coupling assembly at the swing motor.
Attach a 34,450 kPa (5,000 psi) pressure sensor to pressure fitting (D10) for delivery pressure of the auxiliary pump.
Install tooling (C) on the engine to monitor engine speed.Test Procedure
To prevent personal injury or equipment damage from failure of the hydraulic test equipment or associated circuit components because of blocked pump flow, make sure that the test equipment valves are fully open before starting the engine.
To prevent personal injury and/or equipment damage from failed lines or components while the hydraulic test equipment is returned to the open flow position, slowly open the hydraulic test equipment valve while monitoring the pump flow.If pump flow does not increase as the valve is opened, shut the engine off and determine what is preventing the pump from upstroking.
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Enter the service mode on the monitor.
Input the password "9992".
Select "Override Parameters".
Override "Desired Engine Speed" to 1800 rpm.
Illustration 7 g02599896
Portable hydraulic tester (flow meter)
(D1) Portable hydraulic tester (flow meter)
(17) Valve
Turn valve (17) on the portable hydraulic tester clockwise. Record pump flow at the following
Illustration 4 g06033632
Flow meter tool layout
Tooling (D)
( 1) Auxiliary pump
(2) Delivery line for auxiliary pump
(3) Makeup line
(4) Seal
(5) Elbow
(6) Swing motorAuxiliary Pump
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 5 g06032484
Pump compartment
(1) Auxiliary pump
(2) Delivery line for auxiliary pump
Position the machine on level ground.
Stop the engine.
Release pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 5.
Disconnect delivery line (2) from auxiliary pump (1).
Install seal (D16) and plug (D15) to the end of the delivery line (2).
Assemble and install seal (D14), coupling (D13), seals (D4), fitting (D12), seal (D11), fitting (D10), and fitting (D5) on the auxiliary pump.
Illustration 6 g06033643
Swing motor (top view)
(3) Makeup line
(4) Seal
(5) Elbow
Disconnect makeup line (3) from elbow (5) at the swing motor.
Assemble and install seals (D18), tee (D19), adapter (D17), seal (D4), and fitting (D5) to elbow (5) at the swing motor.
Install seal (4) and makeup line (3) to tee (D19).
Remove 311-1362 Vacuum Cap and install the filler plug for the hydraulic tank.
Connect portable hydraulic tester (D) and test hoses between coupling assembly at the auxiliary pump and coupling assembly at the swing motor.
Attach a 34,450 kPa (5,000 psi) pressure sensor to pressure fitting (D10) for delivery pressure of the auxiliary pump.
Install tooling (C) on the engine to monitor engine speed.Test Procedure
To prevent personal injury or equipment damage from failure of the hydraulic test equipment or associated circuit components because of blocked pump flow, make sure that the test equipment valves are fully open before starting the engine.
To prevent personal injury and/or equipment damage from failed lines or components while the hydraulic test equipment is returned to the open flow position, slowly open the hydraulic test equipment valve while monitoring the pump flow.If pump flow does not increase as the valve is opened, shut the engine off and determine what is preventing the pump from upstroking.
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Enter the service mode on the monitor.
Input the password "9992".
Select "Override Parameters".
Override "Desired Engine Speed" to 1800 rpm.
Illustration 7 g02599896
Portable hydraulic tester (flow meter)
(D1) Portable hydraulic tester (flow meter)
(17) Valve
Turn valve (17) on the portable hydraulic tester clockwise. Record pump flow at the following
Parts hydraulic Caterpillar catalog:
2582601
HYDRAULIC AR
262C, 262C2
262C, 262C2
2720957
HYDRAULIC AR
906H, 907H
906H, 907H
2648771
HYDRAULIC AR-BIODEGRADABLE OIL
323D L, 323D LN, 323D2 L
323D L, 323D LN, 323D2 L
2705713
HYDRAULIC AR
323D L, 323D LN
323D L, 323D LN
2949999
HYDRAULIC AR
330D MH
330D MH
2582428
HYDRAULIC AR
246C, 256C, 277C, 277C2, 279C, 279C2
246C, 256C, 277C, 277C2, 279C, 279C2
3046744
HYDRAULIC AR
262C, 262C2, 272C
262C, 262C2, 272C