HYDRAULIC MOTOR A137893 - Caterpillar

Illustration 1 g00786102
Existing solenoid valve for the control of the interaxle differential on the D350E Series II
Illustration 2 g00786995
201-1520 Pressure Control Valve Gp on the D350E Series IIAdaptable To: The new 200-4012 Selector Fork and the new 201-1520 Pressure Control Valve Gp is effective with D350 Series II (S/N: 2XW450-UP).The new 200-4012 Selector Fork and the new 201-1520 Pressure Control Valve Gp are adaptable to D350E Series II (S/N: 2XW1-449), D350E (S/N: 9LR1-UP) and D400E (S/N: 2YR1-UP).Refer to Disassembly and Assembly in order to replace the 7U-4424 Selector Fork with 200-4012 Selector Fork .The oil lines and the fittings for the 201-1520 Pressure Control Valve Gp are unchanged. The existing oil lines and fittings can be used.On the D350E Series II, the new pressure control valve is mounted on the existing bracket in place of the existing solenoid valve.On D350E and D400E Articulated Trucks, the solenoid valve for the interaxle differential is located on the inside of the left hand module. It is necessary to manufacture a mounting plate in order to correctly mount the new 201-1520 Pressure Control Valve Gp. Use the following procedure in order to manufacture a mounting plate.
Illustration 3 g00786101
Refer to Illustration 3 and refer to Table 1. Manufacture a plate for the mounting plate. Use a suitable mild steel.
Table 1
Item     Dimension    
A    
112 mm (4.41 inch)    
B    
68 mm (2.68 inch)    
C    
52 mm (2.05 inch)    
D    
14 mm (0.55 inch)    
E    
45 mm (1.77 inch)    
F    
39 mm (1.54 inch)    
G    
11 mm (0.43 inch) Diameter (2 Places)    
H    
100 mm (3.94 inch)    
J    
16 mm (0.63 inch)    
K    
44.5 mm (1.752 inch)    
L    
38.1 mm (1.50 inch)    
M    
12 mm (0.47 inch) Diameter (2 Places)    
N    
6 mm (0.24 inch)    
Illustration 4 g00795384
Refer to Illustration 4 and refer to Table 2. Manufacture two threaded bosses for the mounting plate from a suitable mild steel.
Table 2
Item     Dimension    
P    
20 mm (0.789 inch) Diameter    
S    
11 mm (0.43 inch)    
T     3/8" Thread    
Illustration 5 g00795387
Attach two threaded bosses (1) that were manufactured in step 2 to plate (2) that was manufactured in step 1. Use three welds (3) with a length of 4 mm (0.1575 inch). Refer to Illustration 3.
Allow the mounting plate to cool and paint the mounting plate.
Remove the existing solenoid valve from the machine.
Illustration 6 g00796735
Top view on the D350E and on the D400E
Install mounting plate (4) to the bosses that mounted the existing solenoid valve. Use two 5M-3062 Bolts (5) and two 8T-4122 Hard Washers . Refer to Illustration 6. Install the plate with the welded bosses toward the front of the machine and toward the transmission.
Install pressure control valve (6) to the mounting plate. Use the existing 8T-2501 Bolts (7) for the original solenoid valve.
Remove the fittings from the original solenoid valve and inspect the condition