2024295 IDLER & BEARING AS Caterpillar parts
527, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
Rating:
Alternative (cross code) number:
CA2024295
202-4295
2024295
CA2024295
202-4295
2024295
Weight: 295 pounds 133 kg.
TRACK SKIDDER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 2024295:
Information:
Transmission, SPN 775 FMI 2Conditions Which Generate This Code:
Illustration 1 g01343143
Connection of the downshift switch on the transmission shift lever
This diagnostic code is associated with the downshift switch on the transmission shift lever. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 2 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuits are in the same state.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 775 FMI 2 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (6) for the switch.
Connect the other lead from the multimeter to the normally open contact (7) for the switch.
Measure the resistance between contact 6 and contact 7. Note the resistance.
Disconnect the lead from contact 7 and connect the lead to the normally closed contact (8).
Measure the resistance between contact 6 and contact 8. Note the resistance. Expected Result:The resistance from contact 6 to contact 7 is greater than 5000 ohms, and the resistance from contact 6 to contact 8 is less than 5 ohms.Results:
YES - The resistance from contact 6 to contact 7 is greater than 5000 ohms, and the resistance from contact 6 to contact 8 is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (6) for the switch.
Connect the other lead from the multimeter to the normally open contact (7) for the switch.
Actuate the switch and measure the resistance between contact 6 and contact 7. Note the resistance.
Disconnect the lead from contact 7 and connect the lead to the normally closed contact (8).
Actuate the switch and measure the resistance between contact 6 and contact 8. Note the resistance. Expected Result:The resistance from contact 6 to contact 7 is less than 5 ohms, and the resistance from contact 6 to contact 8 is greater than 5000 ohms.Results:
YES - The resistance from contact 6 to contact 7 is less than 5 ohms, and the resistance from contact 6 to contact 8 is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact 6 of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact 6 and
Illustration 1 g01343143
Connection of the downshift switch on the transmission shift lever
This diagnostic code is associated with the downshift switch on the transmission shift lever. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 2 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuits are in the same state.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 775 FMI 2 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (6) for the switch.
Connect the other lead from the multimeter to the normally open contact (7) for the switch.
Measure the resistance between contact 6 and contact 7. Note the resistance.
Disconnect the lead from contact 7 and connect the lead to the normally closed contact (8).
Measure the resistance between contact 6 and contact 8. Note the resistance. Expected Result:The resistance from contact 6 to contact 7 is greater than 5000 ohms, and the resistance from contact 6 to contact 8 is less than 5 ohms.Results:
YES - The resistance from contact 6 to contact 7 is greater than 5000 ohms, and the resistance from contact 6 to contact 8 is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (6) for the switch.
Connect the other lead from the multimeter to the normally open contact (7) for the switch.
Actuate the switch and measure the resistance between contact 6 and contact 7. Note the resistance.
Disconnect the lead from contact 7 and connect the lead to the normally closed contact (8).
Actuate the switch and measure the resistance between contact 6 and contact 8. Note the resistance. Expected Result:The resistance from contact 6 to contact 7 is less than 5 ohms, and the resistance from contact 6 to contact 8 is greater than 5000 ohms.Results:
YES - The resistance from contact 6 to contact 7 is less than 5 ohms, and the resistance from contact 6 to contact 8 is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact 6 of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact 6 and
Cat SIS web machinery list:
Parts idler Caterpillar catalog:
2061895
IDLER GP-TRACK
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
2024304
IDLER GP-TRACK
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
1514587
IDLER GP-TRACK
527, D6R
527, D6R
2024296
IDLER GP-TRACK
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
7T6996
IDLER GP-TRACK
527, D6H, D6H II, D6H XL, D6H XR, D6R
527, D6H, D6H II, D6H XL, D6H XR, D6R
1593658
IDLER AS
D6R
D6R
2024303
IDLER & BEARING AS
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
2869306
IDLER & BEARING AS
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
3231171
IDLER & BEARING AS
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
2224489
IDLER & BEARING AS
D6R III
D6R III
2373986
IDLER & BEARING AS
D6R III
D6R III
2024303
IDLER & BEARING AS
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
1593658
IDLER AS
D6R
D6R
7T8940
IDLER & BEARING AS
527, D6H, D6H II, D6H XL, D6H XR, D6R
527, D6H, D6H II, D6H XL, D6H XR, D6R
6T3217
IDLER & BEARING AS
D6H, D6H XL, D6H XR, D6R
D6H, D6H XL, D6H XR, D6R
5Q3169
IDLER AS
312
312
1156335
IDLER AS
307, 307B
307, 307B
5G0238
IDLER ASSEMBLY
931, 931B, D3, D3B
931, 931B, D3, D3B
5S0238
IDLER ASSEMBLY
980, D3, D3B
980, D3, D3B
7T3501
IDLER AS
953, 953B, 953C, 953D
953, 953B, 953C, 953D
3231171
IDLER & BEARING AS
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
2869306
IDLER & BEARING AS
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
2774491
IDLER AS
973C
973C