AVSPARE.COM
parts catalog

IMPELLER-PUMP 3315206 - Caterpillar


3315206 IMPELLER-PUMP Caterpillar parts
Rating:
26
Alternative (cross code) number:
CA3315206
331-5206
3315206
Caterpillar 3315206 IMPELLER-PUMP
Weight: 5 pounds 2 kg.

Buy IMPELLER-PUMP 3315206 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 10
  For full view, you need register

Information:


Illustration 1. Location of identification is marked on front end of crankshaft.It is possible that some 3N2957 Crankshaft Assemblies have the "FRT" mark on the wrong end or the "FRT" mark was left off. To tell if the "FRT" mark is on the correct end of the crankshaft, or to identify the front if the mark was not put on the crankshaft, use the information that follows.
The information which follows permits the crankshaft to be checked for correct installation by removing only the flywheel on the rear of the engine and the vibration damper and adapter on the front of the engine. For a standard rotation engine, three teeth on the front crankshaft gear have punch marks. See Illustration 1. One tooth will have four to six punch marks along the top of the tooth. This tooth is used for alignment with the "C" mark on the 4L3407 Idler Gear which it runs against. This tooth is approximately 42° counterclockwise (as seen from the front) from the centerline of the number one journal. The centerline of the number one journal will be in alignment with the centerline of one of the threaded holes in the crankshaft flange. One tooth ficled on the crankshaft gear will not be in alignment with the centerline of this hole.
To find the top center of the crankshaft number one journal when the crankshaft is installed in the engine, it will be necessary to use a dial indicator to find the top dead center position of the number one piston. This will put the top dead center position of the crankshaft 30 degrees counterclockwise from the vertical centerline as shown in Illustration 1 and 30 degrees clockwise as shown in Illustration 2.
The next two teeth counterclockwise (as seen from the front) have two punch marks along the length (top) of the teeth. These two teeth are used for alignment with the "R" mark on one tooth of the 4L3406 Idler Gear when the engine is changed to reverse rotation. There is only one marked tooth on the rear crankshaft gear. See Illustration 2. This tooth has four to six punch marks on the top. It has a location 30° counterclockwise (as seen from the rear) from the centerline of the last crankshaft journal. Since the teeth on the gear are 7.5° apart, one tooth will be in alignment with the center of a threaded hole in the crankshaft flange. The tooth with the four to six punch marks will be the fourth tooth.
This information permits a fast way to tell if the crankshaft is installed backwards, if the "FRT" mark was left off or put on the wrong end of the crankshaft. It does not tell if the teeth are marked correctly or in alignment when viewed with the damper or flywheel removed. It does permit a quick check to determine if the crankshaft is in backwards even if "FRT" isn't stamped on the crankshaft or is stamped on the wrong end. To check

Cat SIS web machinery list:

Caterpillar parts catalog
C32 Locomotive Engine WJD00001-UP
C32 Locomotive Engine WJE00001-UP
TH48-E70-C27I Petroleum Power Train Package AT400001-UP POWERED BY C27 Industrial Engine
C27 Generator Set T4Z00001-UP
C27 Petroleum Engine For Petroleum Well Service Dry Narrow Applications NAR00001-UP
C27 Industrial Engine RAM00001-UP
C32 Industrial Engine NST00001-UP
C32 Petroleum Engine For Petroleum Well Service Side Mount Turbo SDK00001-UP
C27 Industrial Engine JFJ00001-UP
C27 Petroleum Generator Set EGG00001-UP
C27 Rental Generator Set N1B00001-UP
C27 Locomotive Engine WJC00001-UP
C27 Industrial Engine AT400001-UP
C32 Industrial Engine BT400001-UP
24 Motor Grader N9Z00001-UP (MACHINE) POWERED BY C27 Engine
24 Motor Grader E9Z00001-UP (MACHINE) POWERED BY C27 Engine
773G LRC Off-Highway Truck MWH00001-UP (MACHINE) POWERED BY C27 Engine
773G Off-Highway Truck JWS00001-UP (MACHINE) POWERED BY C27 Engine
775G Off-Highway Truck MJS00001-UP (MACHINE) POWERED BY C27 Engine
775G LRC Off-Highway Truck RFM00001-UP (MACHINE) POWERED BY C27 Engine
777G Off-Highway Truck TNM00001-UP (MACHINE) POWERED BY C32 Engine
773G OEM Off-Highway Truck T5T00001-UP (MACHINE) POWERED BY C27 Engine
775G OEM Off-Highway Truck T5F00001-UP (MACHINE) POWERED BY C27 Engine
773G OEM Off-Highway Truck T5S00001-UP (MACHINE) POWERED BY C27 Engine
775G OEM Off-Highway Truck T5W00001-UP (MACHINE) POWERED BY C27 Engine
777G OEM Off-Highway Truck T4Y00001-UP (MACHINE) POWERED BY C32 Engine
777G OEM Off-Highway Truck T5A00001-UP (MACHINE) POWERED BY C32 Engine
777G Off-Highway Truck RDR00001-UP (MACHINE) POWERED BY C32 Engine
777G Off-Highway Truck GT700001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer RM300001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer KK300001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader RM200001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader KK200001-UP (MACHINE) POWERED BY C32 Engine
844K Wheel Dozer K4Y00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer M4R00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader K9X00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader M9P00001-UP (MACHINE) POWERED BY C27 Engine
992K Wheel Loader KK400001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader RM500001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer KK600001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer RM600001-UP (MACHINE) POWERED BY C32 Engine
MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE) POWERED BY C27 Engine
993K Wheel Loader Z8D00001-UP (MACHINE) POWERED BY C32 Engine
993K Wheel Loader Z8Z00001-UP (MACHINE) POWERED BY C32 Engine
MD6310 Rotary Blasthole Drill DLZ00001-UP (MACHINE) POWERED BY C32 Engine
D11 Track Type Tractor KSN00001-UP (MACHINE)
TH48-E70-C27I Petroleum Power Train Package AT400001-UP POWERED BY C27 Industrial Engine
854K Wheel Dozer H8M00001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine
993K Wheel Loader Z4Z00001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer H9K00001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader ZMX00001-UP (MACHINE) POWERED BY C32 Engine
993K Wheel Loader Z4D00001-UP (MACHINE) POWERED BY C32 Engine
D11T TRACK-TYPE TRACTOR JEL00001-UP (MACHINE) POWERED BY C32 Engine
D11T CARRYDOZER TRACK-TYPE TRACTOR JNS00001-UP (MACHINE) POWERED BY C32 Engine
D10T2 TRACK-TYPE TRACTOR JJW00001-UP (MACHINE) POWERED BY C27 Engine
D10T2 TRACK-TYPE TRACTOR RAB00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer MBE00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer KLS00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader DJK00001-UP (MACHINE) POWERED BY C27 Engine


Parts impeller Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.