AVSPARE.COM
parts catalog

IMPELLER 8M6562 - Caterpillar


8M6562 IMPELLER Caterpillar parts 657
Rating:
31
Alternative (cross code) number:
CA8M6562
8M-6562
8M6562
Caterpillar 8M6562 IMPELLER
Weight: 2 pounds 0 kg.

Buy IMPELLER 8M6562 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER,

Compatible equipment models: 8M6562:

WHEEL SCRAPER  657   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:


Illustration 1 g00784570
Park the machine on level ground. Place the machine in the servicing position.
Illustration 2 g00811329
Move the hydraulic lockout control to the UNLOCKED position.
Turn the engine start switch to the ON position.
Move the joysticks and the travel levers/pedals to the full stroke positions in order to relieve the pressure in the pilot lines.
Turn the engine start switch to the OFF position and return the hydraulic lockout control to the LOCKED position.
Illustration 3 g00687449
Slowly loosen the fill/vent plug on top of the hydraulic tank in order to relieve the internal pressure of the hydraulic tank.
After the pressure is relieved, tighten the fill/vent plug.
Open the access door on the right side of the machine.
Illustration 4 g00687481
The case drain filter is located near the pilot oil filter.
Clean the area in order to keep dirt out of the filter base.
Remove the used case drain filter from the filter base.Note: This element is a cartridge type filter. The element cannot be reused.Note: Used filters should always be disposed of according to local regulations.
Clean the filter base.
Illustration 5 g00101502
Coat the seal of a new case drain filter with clean hydraulic oil. Install the new case drain filter in the filter base. Tighten the case drain filter hand tight.
Start the engine and operate the machine slowly for 10 to 15 minutes. Move each cylinder evenly through several cycles.
Return the machine to the servicing position. Check the machine for oil leaks.
Stop the engine.
Illustration 6 g00687286
(A) High temperature range (B) Low temperature range
Maintain the oil level in the low temperature range for a cold machine. Maintain the oil level in the high temperature range for a machine that is at a normal operating temperature.
Illustration 7 g00687449
Slowly loosen the fill/vent plug in order to relieve any pressure. Remove the fill/vent plug in order to add oil, if necessary.
Clean the fill/vent plug. Install the fill/vent plug.
Close the access door.

Caterpillar parts catalog:

Caterpillar parts catalog
657 SCRAPER 19G00001-00516 (MACHINE)


Parts impeller Caterpillar catalog:

8P0960 IMPELLER-CONVERTER
527, 615, 966D, 966F
8E9972 IMPELLER-CONVERTER
525C, 535B, 535C, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K
9W1566 IMPELLER-CONVERTER
834B, 836, 988F, 988F II, 992C, 992D
1157783 IMPELLER-CONVERTER
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 980G
9W5278 IMPELLER-CONVERTER
980G, 980G II, 980H, 980K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.