AVSPARE.COM
parts catalog

INDICATOR GP-AIR FILTER CHANGE 2389828 - Caterpillar



2389828 INDICATOR GP-AIR FILTER CHANGE Caterpillar parts 416D, 420D, 424D, 428D, 430D, 432D, 442D INDICATOR
Rating:
66
Alternative (cross code) number:
CA2389828
238-9828
2389828
Caterpillar 2389828 INDICATOR GP-AIR FILTER CHANGE

Buy INDICATOR GP-AIR FILTER CHANGE 2389828 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compatible equipment models: 2389828:

BACKHOE LOADER  416D   420D   424D   428D   430D   432D   442D   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

also be removed by lifting the cylinder assembly off the piston after the retaining rings (11) have been removed. The cylinder assembly will then have to be turned over in order to remove the retainer rings on the ahead piston.
REMOVING ASTERN PISTON
12-Ahead piston. 13-Astern piston. 14- Springs. 15-Washers. 16-Pins. 17-Retainer rings. 18-Washers. 19-Springs.6. After the retainer rings (11) have been removed, turn the cylinder over so that the astern piston (13) is on top.
Use care in turning over cylinder assembly as the astern piston may fall out if not held in place.
7. Lift off astern piston (13) being careful not to damage the pins (16).8. Remove retainer rings (17), washers (18), springs (19) and lift off cylinder assembly from ahead piston (12).Clutch Assembly
1. Lift cylinder assembly (8) and set it on the ahead piston (12). Install springs (19), washers (18) and retainer rings (17).2. Install springs (14) and washers (15) into place and set astern piston (13) into the cylinder.3. Turn the cylinder assembly (8) over, holding astern piston (13) in place. Install retaining rings (11).4. Install plate assembly (10) on main shaft and bolt FT840 Bracket in place.5. Install ahead clutch drive ring (9) on plate assembly (10).6. Install the clutch plates alternately beginning with a sintered bronze plate.7. Install cylinder assembly (8) on ahead clutch drive ring (9).8. Install astern clutch drive ring and clutch plates in the same sequence as for the ahead clutch.9. Install the clutch spider (3), being careful not to damage the clutch studs, and install stud nuts (2).10. Install bearing retaining nuts (1).Dump Valve Removal and Installation
PREPARING TO REMOVE DUMP VALVE BODY
1-Retainer ring.The clutches contain two dump valves.
REMOVING VALVE BODY1. Remove the valve body using a 5F7344 Block, two 1D4719 Nuts, two L1329 Bolts, two 8B2377 Bolts, two 4B4280 Washers and two 4B4276 Washers.
REMOVING DUMP PISTON FROM BODY
2-Dump piston. 3-Valve body. When installing, be sure the arrow on the dump valve is pointing outward from the clutch cylinder as illustrated. The solid end of the dump valve piston marked "OUT" must also be positioned as illustrated.Clutch Drive Spider and Oil Pump Drive Shaft
Disassembly
The oil pump drive shaft is splined to the spider and can be removed by lifting it straight up from the spider after the four bolts securing the retainer, cover and coupling are removed.1. Using an 8B7551 Bearing Pulling Attachment, an 8B7548 Push Puller, 8B7550 Legs, an 8B7560 Step Plate and an 9H684 Wrench, pull the top bearing assembly (1) from the clutch spider as illustrated.
REMOVING BEARING ASSEMBLY FROM CLUTCH DRIVE SPIDER
1-Bearing assembly. 2-Bearing assembly. 3-Spacer.2. Remove the spacer (3) located between the two bearings.3. Using the same pulling tools with two 91/2" legs in place of the 8B7550 Legs, remove bearing (2).Clutch Drive Spider and Oil Pump Drive Shaft Assembly
1. Heat bearing assemblies (1) and (2) in oil to 200° - 240° F (104° - 115° C) Max. before installation.2. Install bearing (2) on the clutch drive spider.3. Replace the bearing spacer.4. Install bearing assembly (1) with the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
416D Backhoe Loader BFP00001-17198 (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BLN00001-04543 (MACHINE) POWERED BY 3054 Engine
416D Backhoe Loader BFP05178-17198 (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BLN04544-10299 (MACHINE) POWERED BY 3054 Engine
416D Backhoe Loader BGJ00523-01315 (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BKC00502-UP (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BMC00611-UP (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader MBH00001-UP (MACHINE) POWERED BY 3054C Engine
442D Backhoe Loader SMJ00001-UP (MACHINE) POWERED BY 3054C Engine
424D Backhoe Loader CJZ00001-UP (MACHINE) POWERED BY 3054C Engine
428D Backhoe Loader BXC00001-UP (MACHINE) POWERED BY 3054C Engine
428D Backhoe Loader MBM00001-UP (MACHINE) POWERED BY 3054C Engine
432D Backhoe Loader TDR00001-UP (MACHINE) POWERED BY 3054C Engine
416D Backhoe Loader BFP12900-UP (MACHINE) POWERED BY 3054C Engine
420D Backhoe Loader FDP18400-UP (MACHINE) POWERED BY 3054C Engine
420D Backhoe Loader BLN10300-UP (MACHINE) POWERED BY 3054C Engine
430D Backhoe Loader BNK05900-UP (MACHINE) POWERED BY 3054C Engine
430D Backhoe Loader BML04800-UP (MACHINE) POWERED BY 3054C Engine
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine


Parts indicator Caterpillar catalog:

7U3933 INDICATOR GP-AIR FILTER CHANGE
D250D, D250E, D250E II, D25D, D300D, D300E, D300E II, D350E, D400E, D400E II, D40D
8S2541 INDICATOR GP
120G, 12G, 130G, 140G, 14G, 16G, 561C, 816, 930R, 980B, D5, D5B, D5E, D6C, D6D, D6D SR, D6E, D6E SR
2131412 INDICATOR GP-AIR FILTER CHANGE
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C32, G3508, G3512, G3516, PM3508, PM3512, PM3516, TH48-E80
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.